Dolmar AH-3756, Инструкция по эксплуатации

Страница: 8 / 64

8
FUNCTIONAL DESCRIPTION
CAUTION:
•
Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
Fig.1
CAUTION:
•
Always switch off the tool before installing or
removing of the battery cartridge.
•
Hold the tool and the battery cartridge firmly when
installing or removing battery cartridge.
Failure to
hold the tool and the battery cartridge firmly may cause
them to slip off your hands and result in damage to the
tool and battery cartridge and a personal injury.
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION:
•
Always install the battery cartridge fully until the
red indicator cannot be seen. If not, it may
accidentally fall out of the tool, causing injury to
you or someone around you.
•
Do not install the battery cartridge forcibly. If the cartridge
does not slide in easily, it is not being inserted correctly.
NOTE:
•
The tool does not work with only one battery cartridge.
Tool/ battery protection system
The tool is equipped with a tool/battery protection
system. This system automatically cuts off power to the
motor to extend tool and battery life.
The tool will automatically stop during operation if the
tool or battery are placed under one of the following
conditions. In some conditions, the indicators light up.
Overload protection
When the tool is operated in a manner that causes it to
draw an abnormally high current, the tool automatically
stops without any indication. In this situation, turn the
tool off and stop the application that caused the tool to
become overloaded. Then turn the tool on to restart.
Overheat protection for tool/ battery
When the tool/ battery is overheated, the tool stops
automatically without any indication. The tool does not
start even if pulling the switch trigger. In this situation,
let the tool/ battery cool before turning the tool on again.
NOTE:
The battery overheat protection works only with a
battery cartridge with a star marking.
Fig.2
Overdischarge protection
Fig.3
When the remaining battery capacity gets low, the battery
indicator blinks on the applicable battery side. By further use,
the tool stops and the battery indicator lights up about 10
seconds. In this situation, charge the battery cartridge.
Handle mounting positions
CAUTION:
•
Always make sure that the handle is locked in the
desired position before operation.
Fig.4
Depending on the operations, you can set the angle of
the handle either 45°or 90°position on left or right. To
turn the handle, pull the knob and turn the handle as
shown in the figure. The handle is locked in 45°position.
To turn the handle to 90°position, pull the knob again
and turn the handle more.
Switch action
CAUTION:
•
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released.
Fig.5
For your safety, this tool has a dual switching system.
To turn on the tool, press the lock-off button and press
the switch trigger A and B. To turn off the switch, release
either one of the switch triggers. The tool only starts
when pulling the both switch triggers.
Speed change
Fig.6
The strokes per minute can be adjusted just by turning the
adjusting dial. This can be done even while the tool is running.
The dial is marked 1 (lowest speed) to 6 (full speed).
Refer to the table below for the relationship between the
number settings on the adjusting dial and the strokes per
minute.
Number on adjusting dial Strokes per minute (min )
-1
6
5
4
3
2
1
1,800
1,750
1,650
1,500
1,300
1,000
011264