10411 80th Avenue Pleasant Prairie, WI 53158 | Orders and Customer Care: 1-800-574-7665 | Fax: 1-800-323-5932 | Doheny.com
CHAPTER 4
:
STOP AND RUN THE PUMP
Start the Pump
1. Make sure the pump is connected with electricity.
When power is on, the display screen will display
the time.
2. Press one of ECO/CLEAN/BOOST, the pump will
run. The light on the corresponding program will be
lit. No matter what program you select, the pump will
run on 2850RPM for 5 minutes to eliminate the air in
the pump, so the impeller will not dry grind thus to
cause leakage. After high-speed running, the pump
will run the default speed of the selected program.
Stop the Pump
1. Press STOP of the running pump, the pump will
stop. The lights on the screen twinkle.
Change Pump Running Speed
1. When the pump is running ECO/CLEAN/BOOST,
press arrow buttons up or down to change the speed,
each press is for 50RPM. It will save automatically,
no need to press ENTER.
2. Switch between ECO/CLEAN/BOOST during pump
operation, the pump will not run 5 minutes high
speed again.
3. For MODE 1 and MODE 2, to change speed of S1
and S3, first press CLEAN, if not work, you will
need to stop the pump first. After 5 minutes high
speed running, press CLEAN, then press arrow
button to increase or decrease RPM. When press
MODE 1 or MODE 2 again to run the pump, S1 and
S3 will run as just selected.
To adjust S2 and S4, first press ECO, if not work,
you will need to stop the pump. After 10 minutes
high speed running, press ECO, then press arrow
button to increase or decrease RPM . When press
MODE 1 or MODE 2 again, S2 and S4 will run as
just selected.
NOTE
: RPM for S2 and S4 or S1 and S3 are always
the same. The default for S1 and S3 is 2400RPM, the
adjustable range is 2400 to 2850RPM. The default for
S2 and S4 is 1500RPM.The adjustable range is 1000
to 2400PRM.
Pump Run Under Pre-Programmed Conditions
Pump has three quick start button ECO / CLEAN /
BOOST, as below image. The default speed is 1500,
2400, 3250RPM respectively.
1. Be sure the pump is power on.
2. Press one of ECO/CLEAN/BOOST, the LED light
on screen will be lit.
3. The screen will display STUP for 1 second, and run
2850PRM for 5 minutes. After 10 minutes, the
pump will run on the selected speed.
CHAPTER 5
:
PUMP RUN UNDER MODE1 / MODE2
Mode 1 / Mode 2 Introduction
Running hours and RPMS are all adjustable.
ECO
Indicator Light
1000-2400RPM
Default: 1500
2400-2850RPM
Default: 2400
2850-3450RPM
Default: 3250
CLEAN
BOOST
MODE 1 - 16 Hour Running Cycle
Stage Start Running Default
Quick
Time Hour Speed Start
S1 6:00
am
3
adjustable
2400 RPM CLEAN
S2 9:00
am
5
adjustable
1500 RPM
ECO
S3 6:00
pm
3
adjustable
2400 RPM CLEAN
S4 9:00
pm
5
adjustable
1500 RPM
ECO
MODE 2 - 24 Hour Running Cycle
Stage Start Running Default
Quick
Time Hour Speed Start
S1 12:00
pm
6
adjustable
1500 RPM
ECO
S2 6:00
am
3
adjustable
2400 RPM CLEAN
S3 9:00
am
9
adjustable
1500 RPM
ECO
S4 6:00
pm
6
adjustable
2400 RPM CLEAN
