GETTING TO KNOW YOUR VEHICLE
89
Activation
The Dynamic Centerline feature can be activated
through the Uconnect Settings by pressing the
Cargo Camera soft button, followed by the “Adjust
Centerline” soft button on the touchscreen.
If the Dynamic Centerline feature is turned on, the
overlay will display anytime the Cargo Camera
image is displayed.
Adjusting Centerline
Follow the steps below to manually adjust the
centerline:
1. Press the “Adjust Centerline” soft button
located in the bottom right corner of the
Cargo Camera display.
2. Use the arrows on the bottom left corner of the
Cargo Camera display to adjust the centerline
horizontally or vertically.
3. Once the desired position is achieved, press
the “Accept” button to set the centerline to the
newly specified position.
Deactivation
The Dynamic Centerline feature will automatically
be deactivated whenever the Cargo Camera
display is deactivated. It can also be manually
deactivated through the Uconnect Settings
Ú
page 247.
NOTE:
If the vehicle speed remains below 8 mph
(13 km/h), the Cargo Camera image will be
displayed continuously until the touchscreen
button "X" to disable display of the Cargo
Camera image is pressed.
The touchscreen button “X” to disable the
display of the camera image is made available
ONLY when the vehicle is not in reverse.
If snow, ice, mud, or any foreign substance
builds up on the camera lens, clean the lens,
rinse with water, and dry with a soft cloth. Do not
cover the lens.
Turning Cargo Camera On Or Off — With
Uconnect 5/5 NAV
1. Press the “Controls” button located on the
bottom of the Uconnect display.
2. Press the “Cargo Camera” button to turn
the Cargo Camera system on.
NOTE:
Once initiated by the "Cargo Camera" button, the
Cargo Camera image will be displayed until the
vehicle speed remains below 8 mph (13 km/h)
and the 10 second timer runs out. The image may
be deactivated by pressing the "X" soft button,
placing the ignition in the OFF position, placing the
gear selector in PARK, or pressing the image
defeat “X” button. On deactivation, the previous
selected screen will appear.
B
ED
R
AIL
T
IE
-D
OWN
S
YSTEM
—
I
F
E
QUIPPED
NOTE:
This feature is only available for vehicles equipped
with a RamBox.
CAUTION!
The maximum load per cleat should not exceed
250 lb (113 kg) and the angle of the load on
each cleat should not exceed 45 degrees above
horizontal, or damage to the cleat or cleat rail
may occur.
2
22_DJD2_OM_EN_USC_t.book Page 89
Содержание RAM 2500 2022
