Dodge 2014 SRT Viper Скачать руководство пользователя страница 274 | Manualshive

Страница: 274 / 400

background image

readings to the receiver module. It is particularly impor-
tant for you to check the tire pressure in all of the tires on
your vehicle monthly and to maintain the proper pres-
sure. The TPMS consists of the following components:

•

Receiver module

•

Four TPM sensors

•

Various TPMS messages, which display in the Driver
Information Display (DID)

•

TPM Telltale Light

The Tire Pressure Monitor System (TPMS) will warn the
driver of a low tire pressure based on the vehicle recom-
mended cold placard pressure.

The tire pressure will vary with temperature by about 1
psi (7.0 kPa) for every 12°F (6.5°C). This means that when
the outside temperature decreases, the tire pressure will
decrease. Tire pressure should always be set based on

cold inflation tire pressure. This is defined as the tire
pressure after the vehicle has not been driven for at least
three hours, or driven less than 1 mile (1.6 km) after a
three hour period. The cold tire inflation pressure must
not exceed the maximum inflation pressure molded into
the tire sidewall. Refer to “Tires – General Information”
in “Starting and Operating” for information on how to
properly inflate the vehicle’s tires. The tire pressure will
also increase as the vehicle is driven - this is normal and
there should be no adjustment for this increased pres-
sure.

The TPMS will warn the driver of a low tire pressure if
the tire pressure falls below the low-pressure warning
limit for any reason, including low temperature effects
and natural pressure loss through the tire.

The TPMS will continue to warn the driver of low tire
pressure as long as the condition exists, and will not turn
off until the tire pressure is at or above the recommended

272

STARTING AND OPERATING

«
...
272
273
274
275
276
...
»

Содержание 2014 SRT Viper

















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 SRT Viper

Electronic Parking Disc 3

Бренд: Jacob Jensen Страницы: 2

Бренд: Yakima Страницы: 12

STRONGARM RVR303

Бренд: Blue Giant Страницы: 48

Бренд: Ford Страницы: 37

Бренд: Velleman Страницы: 6

Бренд: Saab Страницы: 3

Бренд: Gator Страницы: 8

Бренд: GMC Страницы: 20

Бренд: Condor Страницы: 2

Бренд: TBC Страницы: 12

Бренд: Prorack Страницы: 14

LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...

Бренд: Dakota Digital Страницы: 3

Бренд: Volvo Страницы: 24

Бренд: Westin Страницы: 2

Бренд: Softride Страницы: 4

Бренд: WABCO Страницы: 34

Бренд: Prorack Страницы: 15

Бренд: TATA Motors Страницы: 151

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды