Dodge 2014 SRT Viper Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 400

background image

General Information

This device complies with FCC rules Part 15 and Industry
Canada RSS-210. Operation is subject to the following
two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference that may be

received including interference that may cause unde-
sired operation.

NOTE:

•

The transmitter has been tested and it complies with
FCC and IC rules. Changes or modifications not ex-
pressly approved by the party responsible for compli-
ance could void the user’s authority to operate the
device.

•

The term IC before the certification/registration num-
ber only signifies that Industry Canada technical speci-
fications were met.

ELECTRICAL POWER OUTLETS

Your vehicle is equipped with two 12 Volt (13 Amp)
power outlet that can be used to power cellular phones,
small electronics and other low powered electrical acces-
sories.

One power outlet is located on the center console to the
right of the shifter. Push down on the power outlet to
access the opening. Push down on it again to close. This
power outlet is powered when the ignition is in the ON
or ACC position.

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

129

«
...
129
130
131
132
133
...
»

Содержание 2014 SRT Viper

















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2014 SRT Viper

Бренд: Yakima Страницы: 11

Бренд: PullRite Страницы: 10

Бренд: V8 equipment Страницы: 17

Бренд: Motoalliance Страницы: 8

Бренд: Simplicity Страницы: 10

Бренд: GYS Страницы: 32

Бренд: Audiovox Electronics Страницы: 12

Бренд: Rosco Страницы: 12

Бренд: Chevrolet Страницы: 103

Бренд: Peak Страницы: 8

Бренд: Renault Страницы: 239

iCarPlay Direct Connect 2000

Бренд: Monster Страницы: 66

Бренд: Ratio Electric Страницы: 16

Бренд: Mitsubishi Страницы: 300

2013 Accord Sedan

Бренд: Honda Страницы: 26

Бренд: Jeep Страницы: 440

Бренд: Samsung Страницы: 19

Бренд: Samsung Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды