Dodge 2008 Avenger Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 467

background image

Do not run the engine in a closed garage or in confined
areas any longer than needed to move your vehicle in or
out of the area.

If it is necessary to sit in a parked vehicle with the engine
running, adjust your heating or cooling controls to force
outside air into the vehicle. Set the blower at high speed.

WARNING!

If you are required to drive with the deck lid open,
make sure that all windows are closed, and the
climate control blower switch is set at high speed.
DO NOT use the recirculation mode.

Safety Checks You Should Make Inside The
Vehicle

Seat Belts
Inspect the belt system periodically, checking for cuts,
frays and loose parts. Damaged parts must be replaced
immediately. Do not disassemble or modify the system.

Front seat belt assemblies must be replaced after a
collision. Rear seat belt assemblies must be replaced after
a collision if they have been damaged (bent retractor, torn
webbing, etc.). If there is any question regarding belt or
retractor condition, replace the belt.

Airbag Light
The light should come on and remain on for six to eight
seconds as a bulb check when the ignition switch is first
turned ON. If the LED is not lit during starting, have it
checked. If the light stays on or comes on while driving,
have the system checked by an authorized dealer.

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

79

2

«
...
79
80
81
82
83
...
»

Содержание 2008 Avenger




















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 Avenger

Бренд: Yakima Страницы: 11

2011 grand cherokee

Бренд: Jeep Страницы: 22

2013 Grand Cherokee

Бренд: Jeep Страницы: 704

Бренд: Jeep Страницы: 558

Бренд: K&M Страницы: 3

Sprinter Bed System Adventure Wagon Kit

Бренд: FVC Страницы: 8

Бренд: Trailboss Страницы: 8

Бренд: Phonocar Страницы: 2

Бренд: WABCO Страницы: 32

Бренд: TATA Motors Страницы: 136

Бренд: Parkeon Страницы: 43

Бренд: Rugged Ridge Страницы: 3

Бренд: Fiat Страницы: 284

Бренд: Voxx Electronics Страницы: 15

TuneBase F8Z442

Бренд: Belkin Страницы: 162

Бренд: Ranger design Страницы: 22

Бренд: Axxess Страницы: 4

Бренд: BMW Страницы: 278

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды