Dodge 2008 Avenger Скачать руководство пользователя страница 358 | Manualshive

Страница: 358 / 467

background image

3. There are two front jacking locations and two rear
jacking locations on each side of the body as shown.

CAUTION!

Do not attempt to raise the vehicle by jacking on
locations other than those indicated in step 3.

4. Turn the jack screw to the left until the jack can be
placed under the jacking location. Once the jack is
positioned, turn the jack screw to the right until the jack
head is properly engaged with the lift area closest to the
wheel to be changed. Do not raise the vehicle until you
are sure the jack is securely engaged.

WARNING!

Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and
hurt someone near it. Raise the vehicle only enough
to remove the tire.

5. Raise the vehicle by turning the jack screw to the right,
using the swivel wrench. Raise the vehicle only until the
tire just clears the surface and enough clearance is
obtained to install the spare tire. Minimum tire lift
provides maximum stability.

6. Remove the wheel nuts, and pull the wheel and wheel
covers (where applicable) off the hub. Install the spare
wheel and wheel nuts with the cone shaped end of the
nuts toward the wheel. Lightly tighten the nuts. To avoid
the risk of forcing the vehicle off the jack, do not tighten
the nuts fully until the vehicle has been lowered.

356

WHAT TO DO IN EMERGENCIES

«
...
356
357
358
359
360
...
»

Содержание 2008 Avenger




















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 Avenger

Бренд: Raven Страницы: 24

Бренд: Weather Guard Страницы: 4

Бренд: Car-Interface Страницы: 23

Бренд: RuggON Страницы: 2

Бренд: Buick Страницы: 428

Бренд: GMC Страницы: 499

Бренд: Kia Страницы: 290

Бренд: SnapPad Страницы: 5

Бренд: Whispbar Страницы: 77

Бренд: B-Speech Страницы: 24

Бренд: Kargo Master Страницы: 6

BTFREQ PRO BTFMPD3SR

Бренд: Scosche Страницы: 16

Бренд: Hyundai Страницы: 19

Бренд: iDataLink Страницы: 6

Бренд: Jeep Страницы: 374

Бренд: Peiying Страницы: 32

iTrip Bluetooth

Бренд: Griffin Technology Страницы: 6

Pajero Pinin 1999

Бренд: Mitsubishi Страницы: 919

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды