Dodge 2008 Avenger Скачать руководство пользователя страница 375 | Manualshive

Страница: 375 / 467

background image

5. Approximately 15 seconds later, one of two things will
happen:

a. The MIL will flash for about 10 seconds and then
return to being fully illuminated until you turn OFF
the ignition key or start the engine. This means that the
vehicle’s OBD II system is not ready and you should
not

proceed to the I/M station.

b. The MIL will not flash at all and will remain fully
illuminated until you turn OFF the ignition key or start
the engine. This means that the vehicle’s OBD II
system is ready, and you can proceed to the I/M
station.

If the OBD II system is not ready, you should see an
authorized dealer or repair facility. If this vehicle was
recently serviced or had a battery failure or replacement,
you may need to do nothing more than drive the vehicle

as you normally would in order for the OBD II system to
update. A recheck with the above test routine may then
indicate that the system is now ready.

Regardless of whether the vehicle’s OBD II system is
ready or not ready, if the MIL is illuminated during
normal vehicle operation, you should have the vehicle
serviced before going to the I/M station. The I/M station
can fail the vehicle because the MIL is on with the engine
running.

REPLACEMENT PARTS

Use of genuine Mopar

t

parts for normal/scheduled

maintenance and repairs is highly recommended to en-
sure the designed performance. Damage or failures
caused by the use of non-Mopar

t

parts for maintenance

and repairs will not be covered by the manufacturer’s
warranty.

MAINTAINING YOUR VEHICLE

373

7

«
...
373
374
375
376
377
...
»

Содержание 2008 Avenger




















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2008 Avenger

Бренд: AAMP of America Страницы: 6

Бренд: Camoplast Страницы: 60

Бренд: Jabra Страницы: 10

Бренд: Yakima Страницы: 11

Бренд: Kargo Master Страницы: 5

Бренд: Yakima Страницы: 8

FRONT HEADLIGHT LENS COVER

Бренд: Bimmer Jakes Страницы: 4

Бренд: Honda Страницы: 73

SmartDiag2GO GD201-O

Бренд: OCTO Страницы: 5

Multiple G9F18 AU000

Бренд: Genesis Страницы: 3

Бренд: MASCOT Страницы: 12

Polaris TATOU 4S

Бренд: Camoplast Страницы: 13

Бренд: Parkeon Страницы: 43

Бренд: Meta System Страницы: 16

Бренд: ICON Страницы: 4

Бренд: Pontiac Страницы: 486

Бренд: Connects2 Страницы: 2

Бренд: Quadratec Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды