DMP Electronics XR200 Скачать руководство пользователя страница 2

Страница: 2 / 56

MODEL XR200

COMMAND PROCESSOR

PROGRAMMING GUIDE

FCC NOTICE

This equipment generates and uses radio frequency energy and, if not installed and used properly in strict accordance with

the manufacturer's instructions, may cause interference with radio and television reception. It has been type tested and

found to comply with the limits for a Class B computing device in accordance with the specification in Subpart J of Part 15

of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. If

this equipment does cause interference to radio or television reception, which can be determined by turning the equipment

off and on, the installer is encouraged to try to correct the interference by one or more of the following measures:

Reorient the receiving antenna
Relocate the computer with respect to the receiver
Move the computer away from the receiver
Plug the computer into a different outlet so that computer and receiver are on different branch circuits

If necessary, the installer should consult the dealer or an experienced radio/television technician for additional suggestions.

The installer may find the following booklet, prepared by the Federal Communications Commission, helpful:

"How to identify and Resolve Radio-TV Interference Problems."

This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402

Stock No. 004-000-00345-4

Information furnished by DMP is believed to be accurate and reliable.

This information is subject to change without notice.

Содержание XR200

























































Результаты поиска

Содержание XR200

Отзывы:

Похожие инструкции для XR200

Бренды по названию

Популярные бренды

DMP Electronics XR200, Руководство по программированию

Результаты поиска

Содержание XR200

Отзывы:

Похожие инструкции для XR200

Бренды по названию

Популярные бренды