2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
SC Series Keypad Installation
3
Option 1 Program Initialization
This option sets all programing options except Programming
Access Code to their factory default values. Press 1 and hold for
two seconds until keypad beeps once.
Option 2 Clearing User Codes
To clear all user codes from the memory, press 1 and hold for two
seconds until keypad beeps once. All user codes are now cleared
and user code 0099 (99 CMD) is placed in user number eight.
Option 3 Bus address
Set the bus address from 00 to 99. It is not necessary to enter a
leading zero for addresses 01 to 09.
Option 4 LX-Bus Communication
This option allows communication of local zone conditions to a
supervising XR200 or XR200-485. Enter 0 (none) when zone
conditions are not sent to the supervising panel. Enter 1 (711
style) when all four local zone conditions are combined as one
zone on the LX-Bus. Enter 4 (714 style) when each local zone
condition is individually sent on four consecutive addresses of the
LX-Bus.
Option 5
This option reserved for future use.
Option 6
This option reserved for future use.
Option 7 Bell Cutoff Time
This option selects the maximum time in minutes (0-15) that the
Bell Output will allow a bell or siren to sound. If the Bell Output is
manually silenced or the system is disarmed, the cutoff time is
reset. Enter 0 to provide continuous bell output with no cutoff.
Options 8, and 9 Exit and Entry Delays
These options set the delay time (0-99 seconds) for Exit Delay
and Entry Delay. When the system is armed, the Exit Delay time
starts and any activity on Burglary Zones is ignored until the exit
delay expires. For an Entry Delay, the system must be disarmed
before the delay expires or an alarm condition will occur. Select
the amount of time desired for each delay.
Option 10 Internal Speaker/Siren Annunciation
This option enables the internal speaker to turn on siren tones for
an alarm anytime the Bell Output is turned on. Enter 1 to enable
internal speaker/siren annunciation.
Options 11 Panic Keys
Select 1 to allow two-button panic key operation. Enter 0 to inhibit
panic key operation.
Option 12 Zone 4 Panic or Fire Selection
This option determines Zone 4 operation as either a Panic or
Fire zone. Choose either option 1 for Panic zone without the Bell
Circuit and without LED alarm status (silent), or 2 for Panic zone
with Bell Circuit and LED alarm status, or 3 to select this zone as
a Fire zone.
Option 13 Relay Action
This option is only available in the 741 and 743 keypads and
determines the keypad relay output operation. Enter 1 for alarm
relay, 2 for door access relay operation, or 3 for sensor reset.
When configured as alarm relay, the relay turns on anytime the
Bell Output turns on.
Option 14 Battery Test
Enter 1 when installing a 741 or 743 keypad and battery backup
voltage monitoring is desired. Low battery is detected at 11.9
VDC.
Option 15
This option reserved for future use.
Option 99 Programming Access Code
This option sets the four digit code (0000-9999) for a programming
access code.
Option 00 Exiting the Program Mode
When programming is completed, press the SPECIAL key and 00
to terminate the Program Mode. The Program Mode will be
terminated if no key is pressed for one minute.
Programming Access Code Initialization
The 740, 741, and 743 keypads can be initialized to reset the
programming access code to the factory default (0000). To reset
the programming access code:
•
Disconnect the Red wire from the 12VDC power source and
disconnect the Red/Black battery wire.
•
Disconnect the Yellow (data transmit) and the Green (data
receive) wires from the LX-Bus.
•
Twist the Yellow and Green keypad wires together.
•
Reconnect the Red wire to the 12VDC power source.
The keypad programmer code is now reset to 0000. Reconnect
wires properly.
Programming the keypad
The SC Series keypads provide a Program Mode that allows installers to configure the keypad.
How to get in
You access the Program Mode by pressing 6,6,5,3 (PROG) followed by a four digit (default = 0000) programming access code. Once
you have accessed the Program Mode you are ready to select the various keypad programming options available. During
programming the Trouble LED will pulse to indicate Program Mode. To enter a programming option press the SPECIAL key followed
by the option number (see the Programming Option Table). Enter the selection for that option. After the selection is entered the keypad
will beep once to accept the programming. If an invalid character is entered, the keypad will beep four times and exit the option.
Programming Readout
When a programming option is chosen (SPECIAL XX), the current setting for the option is immediately indicated on the Zone 1 LED.
A single programmed digit pulses the Zone 1 LED (1/3 second ON, 1/3 second OFF) the number of times necessary to indicate digit
one through nine. For the zero digit, the LED turns on for 1.5 seconds.
For multiple programmed digits, the Zone 1 LED pulses (1/3 second ON, 1/3 second OFF) the number of times to equal the first digit.
The LED turns off for two seconds, then the LED pulses (1/3 second ON, 1/3 second OFF) the number of times to equal the second
digit. When a programmed option uses two digits but the first digit is zero, only the second digit will be displayed.
