DLP Design DLP-RFS1280 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 12

DLP Design DLP-RFS1280 Скачать руководство пользователя страница 9

Rev 1.7 (April 2018) 9

¤

DLP Design, Inc.

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Note: In the event that these conditions cannot be met (i.e. co-location with another transmitter), then
the FCC authorization is no longer valid, and the corresponding FCC ID may

not

be used on the final

product. Under these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate FCC authorization.

7.5 OEM PRODUCT LABELING

The end product containing the DLP-RFS1280 must be labeled in a visible area with the following
text:

“Contains FCC ID: SX9RFS2”

L’étiquette d’homologation d’un module d’Innovation, Sciences et Développement économique
Canada devra être posée sur le produit hôte à un endroit bien en vue, en tout temps. En l’absence
d’étiquette, le produit hôte doit porter une étiquette sur laquelle figure le numéro d’homologation du
module d’Innovation, Sciences et Développement économique Canada, précédé du mot « contient »,
ou d’une formulation similaire allant dans le même sens et qui va comme suit:

“Contient IC: 5675A-RFS2 est le numéro d’homologation du module.”

7.6 RF EXPOSURE

This equipment complies with FCC and IC RSS-102 radiation-exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a minimum distance
of 20cm between the radiator and a human body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.

Cet équipement est conforme aux limites d'exposition aux radiations fac et IC CNR-102 établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance
minimale de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être co-implanté ou
fonctionner en conjonction avec toute autre antenne ou transmetteur.

7.7 ADDITIONAL INFORMATION FOR OEM INTEGRATORS

The end user should not be provided with any instructions on how to remove or install the
DLP-RFS1280. This device has been certified to operate with the antenna models listed below:

x

On-board Chip Antenna

x

Antenna Factor / Linx ANT-2.4-PML-UFL

«
...
7
8
9
10
11
...
»

Содержание DLP-RFS1280













Отзывы:

Нет отзывов