DLP Design DLP-RFS1280 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 12

DLP Design DLP-RFS1280 Скачать руководство пользователя страница 8

Rev 1.7 (April 2018) 8

¤

DLP Design, Inc.

7.0 REGULATORY AGENCY CONSIDERATIONS

7.1 AGENCY IDENTIFICATION NUMBERS

This device complies with Part 15 of the FCC Rules.

Compliance with the appropriate regulatory agencies is essential in the deployment of all transceiver
devices. DLP Design has obtained modular approval for this RF product. As such, an OEM need
only meet a few basic requirements in order to utilize their end product under this approval.
Corresponding agency identification numbers are listed below:

PART NUMBER

US / FCC

CANADA / IC

DLP-RFS1280

SX9RFS2

5675A-RFS2

7.2 EXTERNAL ANTENNAS

The DLP-RFS1280 is preapproved for use with both its on-board chip antenna and an external
antenna (Part No. ANT-2.4-PML-UFL made by Antenna Factor / Linx). Connection to the external
antenna is made via a u.fl connector.

7.3 FCC/IC REQUIREMENTS FOR MODULAR APPROVAL

Any modifications made to the DLP-RFS1280’s printed circuit board, on-board antenna or
pre-approved external antenna could void the user’s authority to operate this equipment. Other
external antennas can be used with the DLP-RFS1280 module so long as the maximum legal radiated
power limit is not exceeded.

7.4 WARNINGS

Operation is subject to the following two conditions: (1) This device may not cause harmful
interference and (2) this device must accept any interference received, including interference that may
cause undesirable operation.

This device is intended for use under the following conditions:

1. The transmitter module may not be co-located with any other transmitter or antenna; and,

2. The module has been approved using the FCC’s “unlicensed modular transmitter approval”
method.

As long as these two conditions are met, further transmitter testing will not be required. However, the
OEM integrator is still responsible for testing their end product for any additional compliance
measures necessitated by the installation of this module (i.e. digital device emissions, PC peripheral
requirements, etc.).

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio

«
...
6
7
8
9
10
...
»

Содержание DLP-RFS1280













Отзывы:

Нет отзывов