DLC SA-230FA Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 38

DLC SA-230FA Скачать руководство пользователя страница 8

7

4. Installation

4.1 Environment

This equipment has been designed for use in accordance with the International EMC

(Electromagnetic Compatibility) Standards. In view of different environments, please follow the

instructions given below to eliminate interference, if necessary.

-

Move the equipment or rotate its direction;

-

Enlarge the space between the equipment and other machines;

-

Put the plug into other outlets;

-

Please consult with the local distributor or qualified electrician.

-

Regarding the environmental temperature for installation, please refer to “9.

Specifications”.

4.2 Install the sterilizer

Caution:

Please read and follow “5.2” on Page 12 in order to understand the operation of

the sterilizer.

Caution:

While installation; please make sure that the bearing capacity of installation table

is enough to carry the sterilizer. For the weight information of the sterilizer,

please refer to “Specifications”.

Caution:

Position the sterilizer on a stable laboratory bench or work surface, ensuring at

least 10 cm clearance between the wall or other pieces of equipment and the

sides of the unit for free circulation of air.

Caution:

Make sure that the door can be opened freely after installation.

Warning:

Do not install or operate the sterilizer in areas where flammable items or volatile

substances are used or stored. An explosion could occur, causing personal

injury. An installation site with good air circulation is required.

«
...
6
7
8
9
10
...
»

Содержание SA-230FA







































Отзывы:

Нет отзывов