background image

DIXON

-43

MAINTENANCE

Briggs & Stratton Engine - 22 HP

Loosen screws and remove air filter cover.

1. 

Remove the filter cartridge by pulling upwards 

2. 

along the outside edge.

IMPORTANT INFORMATION

Operating the engine with loose or damaged 
air cleaner components could allow unfiltered 
air into the engine causing premature wear 
and failure.

IMPORTANT INFORMATION

Do not use compressed air to clean the air 
filter.
Do not wash the paper filter.
Do not oil the paper filter.

WARNING!

The engine and the exhaust system 
become very hot during operation. 
Risk for burns if touched.

Allow engine and exhaust system to 
cool at least two (2) minutes.

Remove the foam filter (precleaner). Clean 

3. 

the foam filter with mild detergent and water. 

Squeeze dry in a clean cloth. Do not oil the 
foam sleeve.

Tap the paper filter against a fixed surface to 

4. 

remove dust. If the paper filter is still dirty, it 

must be replaced.

Wipe clean the inside of air filter housing.

5. 

Refit the foam filter (pre filter).

6. 

8009-406

Loosen cover screws

8019-014

Remove filter

8019-015

Reinstall filter

Mount the filter in the air filter housing.

7. 

Replace the cover over the air filter housing 

8. 

and secure with screws.

Содержание SPEEDZTR 36/965882201 SPEEDZTR 44 / 965882301 SPEEDZTR 48 / 965882401













































































Отзывы: