Dixon Bayco FloTech FT555 Series Скачать руководство пользователя | Manualshive

Страница: 8 / 30

background image

FloTech FT555 Automatic Truck Overfill System Tester

Page 8

10784PA Rev G

FT555 Truck Tester

Go to section

Initial Startup Screen

Normal Startup - After Display Language
Has Been Setup

Press and release the ON/OFF button once. The FT555PA/PW will
show the screen below:

Initial Startup Screen

After the FT555PA/PW starts/restarts, the following screen will be
shown in the selected display language.

The screen above will be the initial display screen every time the
FT555PA/PW Automatic Truck Tester is turned on. This screen
shows the firmware version of the FT555PA/PW and the battery
health status in bars. 5 bars represent full battery capacity.

If the bars displayed are 2 or less, a warning beep will sound and a
warning message (see below) will flash for a few seconds.
Batteries should be changed at your next convenience.

FT555 Truck Tester

Version X.XX

Battery Status █ █ █ █ █

FT555 Truck Tester

Version X.XX

WARNING: Battery Low

«
...
6
7
8
9
10
...
»

Содержание FloTech FT555 Series































Отзывы:

Нет отзывов

Похожие инструкции для FloTech FT555 Series

Бренд: Gardena Страницы: 13

Бренд: Oberheim Страницы: 40

Бренд: NEILPRYDE Страницы: 55

Бренд: HANYOUNGNUX Страницы: 4

Бренд: Park House Healthcare Страницы: 6

Бренд: J&M Страницы: 33

Бренд: Quivogne Страницы: 13

Бренд: Kellfri Страницы: 12

SimMan 3G Trauma

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 16

Бренд: laerdal Страницы: 60

Бренд: laerdal Страницы: 4

Resusci Anne Simulator

Бренд: laerdal Страницы: 8

Nursing Baby VitalSim

Бренд: laerdal Страницы: 15

Бренд: Pari Страницы: 12

Бренд: laerdal Страницы: 2

Бренд: laerdal Страницы: 104

Бренд: laerdal Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды