Dixon Bayco FloTech FT555 Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 30

Dixon Bayco FloTech FT555 Series Скачать руководство пользователя страница 26

FloTech FT555 Automatic Truck Overfill System Tester

Page 26

10784PA Rev G

FT555 Truck Tester

Truck ID Module Test

The Truck ID Module will be tested and report the 12 digit serial
number stored inside the ID module. If there is no Truck ID
Module or the test fails the screen will show “TIM not found”

Step 1)

Connect API Extension Test Cable

Step 2)

Move the J-Slot thumb screws to the correct holes to match

the type of socket to be connected. Follow the “O” and “T”
markings on the plug body. Refer to Figure 2, on page 6.

Step 3)

Connect the FT555PA/PW Automatic Truck Tester to the

trailer socket.

Step 4)

Press and release the ON/OFF button to turn on the

FT555PA/PW Automatic Truck Tester. When “Press Key” screen
appears press and release the TEST SELECT button five times so
the “Truck ID Module Test” screen appears.

Step 5)

Press and release the GO button to start the test. When the

test is complete the screen will report the 12 digit serial number or
show “TIM not found”.

Step 6)

Press and release the TEST SELECT” button to move on

to a new test. Press and release the GO to restart the test, or press
and release the ON/OFF button to turn the tester off.

Truck ID Module Test

TIM Detected

Ser Num: 0000013338F6

«
...
24
25
26
27
28
...
»

Содержание FloTech FT555 Series































Отзывы:

Нет отзывов