Dixon Bayco FloTech FT555 Series Скачать руководство пользователя | Manualshive

Страница: 6 / 30

background image

FloTech FT555 Automatic Truck Overfill System Tester

Page 6

10784PA Rev G

FT555 Truck Tester

Unpack Unit and Initial Setup

Step 1)

When unpacking the FT555 Automatic Truck Tester you

will find the following:

a) FT555 Automatic Truck Tester
b) Two “D” size batteries
c) Three J-Slot thumb screws
d) This instruction manual

Step 2)

Screw in the three J-Slot Screws into the threads marked

“O” for Optic socket compatibility and into the J-Slot threads
market “T” for thermistor socket compatibility.

Step 3)

Remove the battery door by turning counter clock wise

until door opens. Insert two “D” size batteries with positive
battery terminal facing out of the opening. Reinstall battery door
by turning clockwise.

DO NOT FORCE BATTERY DOOR OPEN OR CLOSE

Power On/Off

Press and release the ON/OFF button once to turn the tester on.
Press and release the button again to turn the tester off. The tester
has a display back light for dark conditions. After turning on the
tester, press and hold the ON/OFF button for 2 seconds and the
back light will turn on. Press and hold again for 2 seconds and the
back light will turn off.

«
...
4
5
6
7
8
...
»

Содержание FloTech FT555 Series































Отзывы:

Нет отзывов

Похожие инструкции для FloTech FT555 Series

ImageQuant LAS 4000

Бренд: GE Страницы: 86

Бренд: GE Страницы: 160

Бренд: GE Страницы: 134

Бренд: TC Electronic Страницы: 2

Бренд: Bahco Страницы: 131

Бренд: Bahco Страницы: 126

Бренд: Bard Страницы: 36

Бренд: Bard Страницы: 2

Бренд: Bard Страницы: 30

Бренд: Bard Peripheral Vascular Страницы: 44

Бренд: Fayat Group Страницы: 50

Бренд: Halyard Страницы: 88

Бренд: Gebhardt Anlagentechnik Страницы: 152

Бренд: Hach Страницы: 58

Бренд: Hach Страницы: 52

Бренд: Macht Dental Страницы: 8

Бренд: Uchida Yoko Страницы: 40

Бренд: Yamaha Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды