background image

Note: Be certain the compressed air is off and the pressure relieved 

before servicing any components that contain compressed air. 

6. Follow the manufacturer’s maintenance schedule for the compressed air filters.

7. Tighten the couplings of the valves for the reverse jet pulse cleaning.

8. Remove any moisture that has accumulated in the compressed air manifold and

accumulator.

9. Inspect and clean diaphragm valves. A thorough cleaning normally rectifies operational

problems with valves; however any worn or damaged parts are to be replaced. Use the

following procedure to inspect and repair valves:

A. Main Diaphragm

a. Switch off air supply and drain the system.

b. Unscrew the main diaphragm cover bolts and remove the valve cover.

c. Inspect the spring and diaphragm for dust and damage. Remove dust with water and

replace damaged parts with diaphragm repair kits for 1” or 1.5” valves.

d. Replace valve cover and valve cover bolts.

B. Solenoid Diaphragm

a. Switch off air supply and drain the system.

b. Unscrew the bonnet bolts and remove the bonnet.

c. Inspect the diaphragm for dust and damage. Remove dust with water and replace

damaged parts with diaphragm repair kit for 1” or 1.5” valves.

d. Replace the valve bonnet and valve bonnet bolts.

C. Solenoid Coil

a. Switch off air supply and drain system.

b. Apply proper voltage to the coil and listen for a pronounced “Click” as the pole

moves.

c. If a pronounced “Click” occurs and the valve does not function follow instructions

for replacing the main diaphragm and solenoid diaphragm.

d. If the “Click” is not heard, replace the solenoid with either a part for the 1” valve or

for the 1.5” valve.

10. Check and replace if necessary the access door gaskets and dust drawer gaskets if

applicable.

Cartridge Filter Replacement 

Note: Depending on the contaminant being collected, it is advised to wear a 

dust respirator when handling dirty filters. 

Turn the “T” handles counter-clockwise until clearance is obtained above the cartridge filter. 

Remove top cover from top of filter. Slide plastic bag over filter and pull it down to cover top 

filter and remove. Cover the bottom filter with a plastic bag and remove. Repeat this with all 

filters. 

Содержание WB-4000-D















Отзывы:

Похожие инструкции для WB-4000-D