background image

11

Operation Precautions

COMPLETELY READ AND UNDERSTAND THIS 

MANUAL BEFORE ATTEMPTING TO OPERATE 

THE SNOW BLOWER

1.  Keep all safety guards in place and in proper working order at 

all times.

2.  NEVER place fingers, hands, or body near the snow blower 

when it is running. Do not lean or reach over the snow blower 

when the machine is running.

STOP THE ENGINE TO UNCLOG THE DISCHARGE 

CHUTE. NEVER USE YOUR HAND TO CLEAN OUT 

THE DISCHARGE CHUTE OR AUGERS.

3.  Always stop the engine to dislodge snow from the discharge 

chute or from the augers. Wait ten seconds for the augers to 

stop rotating. Never use your hands to clear out the augers or 

discharge chute. Always use the clear-out tool provided or a 

similar tool.

4.  Keep all people (except the operator) a minimum of 25 feet 

from the snow blower during operation.

5.  Always aim the discharge chute away from people and animals.

6.  Do not leave the snow blower unattended when it is running. 

Turn off the engine before leaving the area.

7.  Do not use this piece of equipment while tired or under the 

influence of drugs, alcohol or medication.

8.  Parts, especially exhaust system components, get very hot 

during use. Stay clear of hot parts.

9.  Use extra caution when operating on gravel or other loose 

material.

!

DANGER

!

DANGER

Содержание 106371





























Отзывы: