Dirty Hand Tools 106371 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 28

Dirty Hand Tools 106371 Скачать руководство пользователя страница 9

9

Assembly

Attaching the Discharge Chute

1. Attach the discharge chute to the snow blower by placing it on

the chute seat on the snow blower. Position the flange keeper

beneath the chute seat lip. Align the two holes in the chute and

two holes in the flange keeper and secure with two bolts from

the top side (see Figure 4). Repeat in three locations to attach

the discharge chute to the snow blower.

2. Attach the chute crank bracket aligning the chute notches with

the spiral end of the chute directional control assembly using

the two hex bolts, flat washers and nylon lock nuts from the

hardware kit (see Figure 5). Lubricate both ends of the chute

directional control crank with petroleum jelly, paraffin wax, or

light machine oil.

SKID

SHOE

HEX NUT

(2 PLACES)

Attaching the Wheels

1. Attach both wheels by lining up the holes in the rim with both

holes in the axle and securing with the attached d-rings.

Adjusting the Skid Shoes

1. Position the skid shoes based on surface conditions. Adjust

upward for hard-packed snow. Adjust downward when

operating on gravel or crushed rock surfaces. Loosen the two

hex nuts that retain the skid shoe in place and move up or

down as desired, then retighten the lock nuts (see Figure 6).

Repeat for the opposite side of the snow blower.

Figure 6

CHUTE

SEAT

DISCHARGE

CHUTE

Figure 5

FLANGE
KEEPER

CHUTE DIRECTIONAL

CONTROL

DISCHARGE

CHUTE

Figure 5

«
...
7
8
9
10
11
...
»

Содержание 106371





























Отзывы:

Нет отзывов