Dirt Devil INFINITY AC DD5110, Инструкция по эксплуатации, Страница: 17 / 152

Preparatory work
Getting to know the appliance
Fig. 1 :
1
dirt container release button;
2
pow-
er button;
3
parking slot;
4
power cord with plug;
5
dirt container lid;
6
shroud;
7
separator;
8
hose
inlet;
9
max mark;
10
wheel cover;
11
cord rewind
button;
12
telescopic tube release catch;
13
telescop-
ic tube;
14
bypass vent;
15
handle;
16
hose connec-
tor;
17
hose;
18
floor nozzle
Accessories (optional)
Fig. 2 :
A
parquet nozzle;
B
flexible hose;
C
mini
turbo brush;
D
3-in-1 combo nozzle
Unpacking and assembling
CAUTION!
If using the mini turbo brush (optional)
(Fig. 2 /
C
), make sure that the surface can with-
stand the rotating brush roller without becoming
damaged.
NOTE:
If you intend to use one of the small accessory
nozzles: We recommend to mount them directly
to the hose handle (Fig.
5
).
1
Check that the unpackaged contents are com-
plete (Fig. 1 ). If you notice any transport damage or
if anything is missing, contact your dealer immedi-
ately.
2
Insert the hose connector into the hose inlet
of the appliance (Fig. 3 ). Ensure the hose connec-
tor has clicked into place. Check for proper assembly.
3
Slot the telescopic tube and hose handle together
(Fig.
4
).
4
Adjust the length of the telescopic tube
as indicated (Fig. 4 ).
5
Mount one of the floor noz-
zles to the telescopic tube. When connecting the two
parts, you might need to twist them a little against
each other (Fig. 5 ).
Vacuum cleaning
CAUTION!
Especially when vacuum-cleaning stairs make
sure that you always stand on a higher level than
the appliance. Otherwise there is a risk that the
appliance will fall and injure you.
NOTE:
In normal situations the bypass vent must be
completely closed. With the bypass vent
(Fig. 1 /
14
) you can quickly reduce the suction
power, e.g. to release curtains that have acciden-
tally been sucked in.
To close the bypass vent, push it down. To open
the bypass vent, push it up.
1
Unwind the power cord but be sure not to pull
the cord beyond the yellow mark. If exceeded, press
the cord rewind button (Fig.
6
).
2
Insert the plug
into an electrical outlet with ground/safety contact.
3
Switch the appliance on by pressing the pow-
er button (Fig.
7
).
4
For use on carpets click rocker
switch of the floor nozzle forward (Fig. 8 /A). For use
on hard floors click rocker switch back (Fig.
8
/B).
Storing the appliance
1
Switch off the appliance and pull the plug from
the mains socket.
2
Push the cord rewind button
(Fig.
6
), until the connection cord has been fully re-
wound.
3
Insert the floor or parquet nozzle which is
connected to the telescopic tube or handle into the
parking slot (Fig. 9 ).
Maintaining the appliance
Emptying and cleaning the dirt container
NOTE:
The motor is equipped with a thermal cut-out. If
for any reason the appliance should overheat, the
thermostat will automatically turn the appliance
off.
1
Press dirt container release button to remove the
dirt container (Fig.
10
).
2
Hold dirt container low
over a bin and press dirt release button to open, al-
lowing dirt to fall out (Fig. 11 ).
3
To remove the sep-
arator, hold the container and rotate the separator
clockwise (Fig. 12 ). Rinse it clean and leave it dry-
ing.
4
Hold the container and turn the shroud an-
ti-clockwise (Fig.
13
). Rinse it clean and leave it dry-
ing. Remove all residual dust from the dirt contain-
er.
5
After cleaning insert the shroud again and lock
it by turning clockwise.
6
After cleaning insert the
separator again and lock it by turning anti-clockwise.
Close the bottom plate of the dirt container.
7
Press
the dirt container firmly into the appliance until you
feel or hear it locking into place (Fig.
14
).
EN
17