Directed 403.TL11 1.15 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 21

Directed 403.TL11 1.15 Скачать руководство пользователя страница 5

5

403.TL11 1.15 2010 Toyota Camry
©2022 VOXX•DEI LLC. All rights reserved.

Pre-installation and application warnings

Firmware notes:

This section highlights important information for this specific firmware and will assist in

pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.

T-Harness

compatible

Keys required for

programming

1

Keys required for

operation

0

Important!

TL11 requires either CAN or IMMO connections. An Analog Firmware is recommended if CAN connections are

NOT

used and the vehicle does

NOT

have a transponder. The TL11 installation guides can be used for wire and connection

details.

Some Toyota 2010+ models have different encryption types. Please look at your key blade and identify the markings. A dot
"." means the vehicle is compatible with TL11 firmware. "G" or "H" indicates the vehicle is not compatible with this firmware.
Refer to "Key Types" for more information.

Note:

some replacement keys may not have any markings on the key.

Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic
connector.

Refer to the "Vehicle connections" following the installation diagram.

General notes:

This section highlights important information for this specific firmware.

[1]

Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.

[2]

The installation of an aftermarket hood pin is

ONLY

required on vehicles that are

NOT

equipped with a factory hood pin or

NOT

supported in data.

[3]

Second starter connection may be required in some vehicles.

«
...
3
4
5
6
7
...
»

Содержание 403.TL11 1.15






















Отзывы:

Нет отзывов