Directed 403.TL11 1.15 Скачать руководство пользователя страница 13

Страница: 13 / 21

403.TL11 1.15 2010 Toyota Camry
©2022 VOXX•DEI LLC. All rights reserved.

Connecting the module

Important!

Make all the required connections to the vehicle, as described in this guide, and double check to ensure everything is correct prior
to moving onto programming.

Warning!

To take advantage of advanced features, you must use DirectLink 4.5 (and higher) or the Directechs Mobile application.

Flashing a module using your computer:
1.

Connect

the interface module to your computer using the

XKLoader2

to www.directechs.com using Internet Explorer, and

select

the Flash Module button.

Follow

the instructions to

select

your vehicle, installation type, and configure your options.

4. Once you have configured the firmware options,

click

on the FLASH button.

Flashing a module using your smartphone or tablet:
1.

Connect

the interface module to your

XKLoader3

Launch

the Directechs Mobile app on your smartphone or tablet.

Select

FLASH YOUR MODULE and

follow

the on screen instructions.

When the flashing operation is successful, you can proceed with the instructions below.

D2D installation

Recommended:

Connect

the 10-pin, 12-pin and 14-pin harnesses to the module, then

connect

the 4-pin D2D harness.

(14-pin)

(10-pin)

(D2D)

(12-pin)

W2W installation

If required:

Connect

the 10-pin and 12-pin harnesses to the module, then

connect

the 14-pin

harness to the module.

(14-pin)

(10-pin)

(12-pin)

Содержание 403.TL11 1.15




















Результаты поиска

Содержание 403.TL11 1.15

Отзывы:

Directed 403.TL11 1.15, Руководство по установке, Страница: 13 / 21

Результаты поиска

Содержание 403.TL11 1.15

Отзывы: