Directed Electronics 871XP, Руководство по установке

Страница: 45 / 55

© 2004 Directed Electronics, Inc. Vista, CA
4 45 5
2 2--1 11 1 CCH HA AN NN NEELL 5 5 V VA ALLIID DIITTY Y//LLA ATTCCH HEED D//LLA ATTCCH HEED D R REESSEETT W WIITTH H IIG GN NIITTIIO ON N//3 30 0--SSEECCO ON ND D TTIIM MEED D//6 60 0--SSEECCO ON ND D TTIIM MEED D//9 90 0--SSEECCO ON ND D
TTIIM MEED D:: Channel Four can be programmed for these output configurations. The unit is set to the default validity output.
To change the configuration, use the two-chirp setting to toggle through the different configurations.
3 3--1 1 EEN NG GIIN NEE CCH HEECCK KIIN NG G O ON N//O OFFFF:: In the default setting the remote start will monitor either the vehicle's tach wire
or voltage depending on the programming of feature 3-2. If programmed OFF the vehicle will crank for the pro-
grammed crank time (feature 3-5) and will not verify with tach or voltage that the car is running. In the OFF
setting, if the vehicle fails to start, the ignition can stay on for the entire run duration. Using tach or voltage
check is always recommended if possible.
3 3--2 2 CCH HEECCK KIIN NG G TTY YP PEE TTA ACCH H//V VO OLLTTA AG GEE:: Selects the method of engine monitoring. If set to TACHOMETER the unit will
reference the learned tach signal to disengage the starter. In addition it will monitor the RPM and shut down if
the engine RPM is too high or too low. When set to VOLTAGE, the unit will crank the starter for the programmed
time and then attempt to sense that the engine is running by detecting an increase in voltage. The threshold
for the voltage check is selectable in feature 3-6.
3 3--3 3 R RU UN N TTIIM MEE 1 12 2,, 2 24 4,, 6 60 0 M MIIN NU UTTEESS:: Selects the time in minutes that the system will operate the engine until
the system "times out". This is the maximum operation period and the system may be shut down using a
shutdown at any time. Using the Bitwriter, the run time can be programmed for any duration from 1-60 minutes.
3 3--4 4 P PA AR RK KIIN NG G LLIIG GH HTTSS FFLLA ASSH HIIN NG G//CCO ON NSSTTA AN NTT:: In the default setting, the unit will flash the vehicle's parking lights (if
connected) while remote started. The constant setting will turn the parking lights on solid for the entire run duration.
3 3--5 5 CCR RA AN NK K TTIIM MEE 0 0..6 6//0 0..8 8//1 1..0 0//1 1..2 2//1 1..4 4//1 1..6 6//1 1..8 8//2 2..0 0//4 4..0 0 SSEECCO ON ND DSS:: If the unit is programmed for no engine check-
ing or voltage sense, the crank time must be set to the appropriate duration. The default setting is 0.6 second.
If a different crank time is desired, select feature 3-5 and select either 0.6 second by using the one-chirp setting
or toggle through the higher settings by using the two-chirp settings.
3 3--6 6 V VO OLLTTA AG GEE CCH HEECCK K H HII//LLO OW W:: This feature only functions when programmed for voltage sense. Some vehicles have
many accessories, which are turned on when remote started. In these vehicles, the variation of voltage between
the engine off and the car running is very small and the remote start unit may "think" the vehicle has not started.
This can cause the remote start to shut-down after the car has been started. If this happens program this feature
to the LOW position.
3 3--7 7 SSH HO OR RTT R RU UN N//TTU UR RB BO O:: When the and buttons on the transmitter are pressed simultaneously, the
vehicle will start for the programmed short run time. The factory default is 1 minute.
m meennuu ##33 -- rreem moottee ssttaarrtt ooppttiioonnss