DINSEO DIX TIG GO 1806.M AC/DC, Руководство по эксплуатации, Страница: 28 / 30

28
Creating and memorising
automatic welding points
Once you have defined the parameters the operator requires to do
their work properly, you can save them in the memory and create
a WELDING PROGRAM by proceeding as follows.
WARNING: To access the setting saving phase, the PRINCIPAL
CURRENT LED I
1
must be switched on without flashing.
1) Hold the “PRG” PROGRAM Key (T2) down for at least 5 con-
secutive seconds until the DISPLAY (D) reads Pr , accompa-
nied by a flashing number (e.g. Pr 1).
In order to be able to choose WELDING PROGRAM that is
free, simply rotate the ENCODER knob (E) and look for a pro-
gram for which the control panel has all the LEDs for the vari-
ous settings switched off.
WARNING: The control panel allows you to save a maximum
of 6 WELDING PROGRAMS.
It is also possible to overwrite a program already saved.
I
2
HOT
START
ARC
FORCE
PULSE
CYCLE
T b
f
T p
I
1 I
p
I
b
PULSE
SYN
FAST
SLOW
WAVE
VRD
CYCLE
Ø
PULSE
SYN
FAST
SLOW
WAVE
T2
D
E
2) To SAVE the PROGRAM hold the “MEM” SAVE Key (T1) down
until the DISPLAY reads “Sto” .
3) The WELDING PROGRAM has now been saved and its num-
ber appears in the DISPLAY (D) along with the other settings
saved (corresponding LEDs on without flashing).
I
2
HOT
START
ARC
FORCE
PULSE
CYCLE
T b
f
T p
I
1 I
p
I
b PULSE
SYN
FAST
SLOW
WAVE
VRD
CYCLE
Ø
I
2
HOT
START
ARC
FORCE
PULSE
CYCLE
T
b
f
T
p
I
1 I p
I
b PULSE
SYN
FAST
SLOW
WAVE
VRD
CYCLE
Ø
PULSE
SYN
FAST
SLOW
WAVE
D
D
T1
PROGRAMMED and/
or MANUAL welding
PROGRAMMED WELDING
When the WELDING PROGRAM has been saved, the operator
can weld using only pre-set values as they cannot edit any type
of parameter / function. To edit, switch to MANUAL welding mode.
MANUAL WELDING
To go back to set / edit the parameters selected or to create a new
program, proceed as follows:
1) Hold the “PRG” PROGRAM Key (T2) down (about
3 seconds)
until the DISPLAY (D) shows the number of the program se-
lected flashing (e.g.
Pr6 ).
I
2
HOT
START
ARC
FORCE
PULSE
CYCLE
T
b
f
T
p
I
1 I
p
I
b
PULSE
SYN
FAST
SLOW
WAVE
VRD
CYCLE
Ø
PULSE
SYN
FAST
SLOW
WAVE
T2
D
2) Turn the ENCODER Key (E) anticlockwise until the DISPLAY
(D) shows 3 dashes.
3) Press and release the “PRG” PROGRAM key (T2) and the weld-
ing power source goes back to the initial operation condition.
4) You can now set or edit the individual parameters or create
new programs.
5) Rotate the ENCODER Knob (E) to scroll the programs until
you find an empty, unused program slot.
Calling up saved programs
1) Hold the “PRG” PROGRAM Key (T2) down (about 3 seconds)
until the DISPLAY (D) shows the number of the program se-
lected flashing (e.g. Pr 6).
2) Turn the ENCODER Knob (E) until the DISPLAY (D) shows
the program number (flashing) you wish to call up (e.g. Pr5).
I
2
HOT
START
ARC
FORCE
PULSE
CYCLE
T
b
f
T
p
I 1 I
p
I
b
PULSE
SYN
FAST
SLOW
WAVE
VRD
CYCLE
Ø
I
2
HOT
START
ARC
FORCE
PULSE
CYCLE
T
b
f
T
p
I 1 I
p
I
b
PULSE
SYN
FAST
SLOW
WAVE
VRD
CYCLE
Ø
PULSE
SYN
FAST
SLOW
WAVE
WAVE
T2
D
D
E
NOTE: If when you are rotating the ENCODER knob (E) to look
for a saved welding program to call up the panel does not have
any LEDs switched on without flashing, this means that the weld-
ing program you are trying to call up has not been saved and, as
a result, cannot be called up!
3) Press and release the “PRG” PROGRAM key (T2) to call up
the program number selected.
4) You can now carry out PROGRAMMED welding.