Dinolift DINO 260XTD Скачать руководство пользователя страница 54

Страница: 54 / 79

Maintenance instructions

•

DINO 260XTD

RL1

Change-over relay on the timer card, switches the voltage supply over from either

the power supply unit or from the battery, depending on whether the power supply

unit is feeding power to the system or not.

RL2

Mains relay on the timer card, controls and switches on and off the mains current of

the control system.

SR2

Safety relay monitoring operation of the outriggers.

The safety relay resets as soon as all the outrigger safety limit switches (RK11,

RK12, RK13 and RK14) have closed. After that it is possible to operate the boom.

SR3

Safety relay, which monitors the outreach to the side. Safety limit switches RK5 and

RK4 controlling operation of the safety relay.

Overloading of the boom: SR3 trips. The safety relay is automatically reset upon

return to the normal outreach range after an overloading situation.

If either the RK4 or the RK5 has failed: The safety relay SR3 trips as soon as

the operating range of the RK5 has been exceeded. The safety relay will not

automatically reset upon return to the operating range of the RK4, and hence the

operation of the electric appliance must be checked.

SR4

Safety relay for the emergency stop; stops the motors and switches off the control

voltage from the boom/chassis selector valve. The relay will trip, if the emergency

stop button S1 or S4 or the chain limit switch RK7 or RK15 cuts off the control circuit

for the relay.

SR5

Safety relay for the outriggers; prevents the operation of the outriggers, if the limit

switch RK3 for the boom is not closed. The relay cuts off the control voltage from the

selector valve (1A) for the chassis and the selector valve (9B) for the outriggers.

Main electric cabinet (LCB), switches

Locking emergency stop switch. Stops all other functions except the emergency

descent and the sound signal, which remain operational. Controls the safety relay

SR4.

Start and stop switch for the combustion engine. Operates only, if the mains current

is not connected.

Selector switch for the speed of the boom movements.

Position 0: boom movements impeded

Position 1: slow boom movements

Position 2: boom movements at full speed

S11

Start switch for the emergency descent, yellow pushbutton.

S16

Turning the boom to the left and right, lever switch (also emergency descent).

S17

Lifting and lowering the boom, lever switch (also emergency descent).

S18

Retracting and extending the telescope, lever switch (also emergency descent).

Содержание DINO 260XTD
















































































Результаты поиска

Содержание DINO 260XTD

Отзывы:

Похожие инструкции для DINO 260XTD

Бренды по названию

Популярные бренды

Dinolift DINO 260XTD, Инструкция по техническому обслуживанию

Результаты поиска

Содержание DINO 260XTD

Отзывы:

Похожие инструкции для DINO 260XTD

Бренды по названию

Популярные бренды