Dinolift DINO 260XTD Скачать руководство пользователя страница 30

Страница: 30 / 79

Maintenance instructions

•

DINO 260XTD

4.3.1.

Inspect thoroughly the support outriggers and the outrigger cylinder joints

check the mechanical structure of the outriggers and the welded seams

The structures must not show signs of deformations or cracks No fractures or cracks are

allowed in the welded seams.

Check the footplates for deformations, cracks or breaches

Also check that the footplate can turn freely on its joint.

Check the condition of the outrigger joints:

1. lower the outriggers slightly

2. swing the outriggers back and forth in the

horizontal plane and check the joints for play

3. check the operation and condition of the limit

switch mechanisms on the outriggers

4. replace any worn out parts

5. lubricate the outrigger joints (see point

“Lubrication plan”)

Lower the outriggers to the support position.

4.3.2.

Check the frame structures, the boom system, the work platform and the

platform carrier

Inspect the chassis

• general condition

• check the attachment of the tow-bar to the chassis

• check the condition of the overrun and its attachment to the chassis.

• check the rims, the tightness of the wheel bolts, the tyres and the tyre pressures The

correct pressure ratings are marked both on the tyres and on the jockey wheel bracket.

• check the condition and play of the wheel bearings

• check the condition of the transport support of the boom

inspect the boom

• extend the telescope and check that there are no permanent deformations, dents or

traces of substantial wear in the boom

• check the welded seams for wear, cracks or breaches

• check the boom attachment for cracks or breaches

• check the bearing and the pin of the boom joint and the locking of the pin

• check the condition of the joint pins and bearings of the articulated arms and the locking

of the pins

• check the play and attachment of the slide pads on the boom Adjust as necessary.

• lubricate the sliding surfaces of the boom system

• check the condition of the cable chain, its clamp brackets as well as the tightness of the

screw connections

• check the condition of the boom end cover

Содержание DINO 260XTD
















































































Результаты поиска

Содержание DINO 260XTD

Отзывы:

Похожие инструкции для DINO 260XTD

Бренды по названию

Популярные бренды

Dinolift DINO 260XTD, Инструкция по техническому обслуживанию

Результаты поиска

Содержание DINO 260XTD

Отзывы:

Похожие инструкции для DINO 260XTD

Бренды по названию

Популярные бренды