DINO 125T
27
The platform movement speed can be increased by turning the speed II -switch simultaneously with
using the lever 17 or 19.
After using the emergency stop -pushbutton the lift is made operational by pressing the emergency
descent -pushbutton. (Signal light 4 C on the chassis control panel goes out)
13. Test functioning of the overload limit switch RK4.
- Platform load about 80 kg (176 lbs)
- Move the boom to horizontal position
- Extend the telescope.
When the movement stops the red overload warning light (18) should light up.
- Compare the actual reach to the figures in the reach diagram (page 6)
Front edge of the platform = reach - 0,5 m (
20 inches)
WARNING !
When the red overload warning light (18) is lit, no additional weight may be placed on the platform
(e.g. a second person, tools or the like)
Example: A single person on the platform extends the telescope, or alternatively somebody
operating the chassis control panel extends it as far as it will go low above the ground.
When the overload warning light lits no load may be added to the platform. The telescope should be
retracted.
IF THE EMERGENCY DESCENT SYSTEM OR OTHER SAFETY DEVICES
ARE NOT FUNCTIONING PROPERLY,
THEY MUST BE REPAIRED BEFORE USING THE UNIT.
15. Check the "daily inspections" list in the service manual and make all the inspections
mentioned therein.
16. With the boom slightly raised and the telescope slightly extended, check that the platform
does not lower itself when no operating controls are used.
17. In cold environments
- the engine should be run for a short time without loading to raise the oil temperature.
- Start operating the unit carefully, making slow movements back and forth without platform
load from the chassis control panel.
Содержание DINO 125T
