manualshive.com logo in svg

Dimplex WB15, Инструкция по эксплуатации

Поделиться
Скачать
Dimplex WB15 Скачать руководство пользователя страница 2

 

2

 
 
 

IMPORTANT HEALTH AND SAFETY INFORMATION 

 

PLEASE READ BEFORE USING YOUR NEW WATER BOILER 
 
Your new water boiler is designed to provide a constant source of near boiling 
water for the preparation of hot drinks. 

THIS IS VERY HOT

  

 
All personnel must be provided with sufficient and appropriate training in the 
safe use of this appliance. 
 
An instruction sheet displayed next to the machine is often helpful in notifying 
users that the appliance contains and dispense near-boiling water. 
 
In line with Health & Safety requirements we recommend that a risk assessment 
be carried out after the boiler has been installed. 
 
It is advisable to display a sign informing customers that drinks made from this 
boiler are very hot. 
 
During normal use of the boiler, certain surfaces will become hot. (especially  
near to the draw off tap). Care should be taken to avoid potential injury from 
burns and scalding whilst operating the appliance. 
 
Disclaimer. This appliance is designed to heat water. No other medium should 
be used. Glen Dimplex UK Ltd will not be held responsible for any accidents or 
injuries that occur from either misuse of the appliance or temperature of water 
or the hot drinks served. 
 
 

Содержание WB15














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды