manualshive.com logo in svg

Dimplex WB15, Инструкция по эксплуатации

Поделиться
Скачать
Dimplex WB15 Скачать руководство пользователя страница 12

 

12

SERVICE WARNING LIGHT (All Models except WB5E) 

 

All models except WB5E have this facility. This light is designed to help you 
discover the cause of any malfunction. If the circuit senses a problem, the 
service light will flash a number of times and then pause and repeat this 
sequence. Count the number of flashes between pauses and refer to the table 
on the back cover. Some serious service problems will disable the boiler whist 
less serious ones will allow you to continue to operate until a convenient time 
arises for the fault to be rectified. 

 
 
 
 

 
 
NUMBER OF 
FLASHES 
BETWEEN 
PAUSES 

MEANING ACTION 

1 Constant  

Water level sensor has scaled up 
at normal level and machine has 
filled to a higher level 

Clean Sensing Probes 

2 

Operating level sensor has been 
detected but lower level sensor 
has not 

Clean Sensing Probes 

3 

Overfill level sensor has been 
detected but other sensors have 
not 

Clean Sensing Probes 

4 

Danger level sensor has been 
detected and machine functions 
have been shut down 

Clean Sensing Probes 

5 

Thermistor or potentiometer have 
failed 

Call service department on 
01704 502911  
Quoting the Serial Number 

6 

Boiler has failed to fill in the 
allotted time. Possible causes :- 

1. 

 Water supply turned off. 

2. 

 Water inlet valve has failed. 

3. 

 Blockage in water inlet pipe. 

4. 

 Pipe connecting inlet valve to 

boiler has become detached.  

5. 

 Bottom sensor is scaled up 

Check water supply 
 
If in order call Instanta 
service department quoting 
the Serial Number 

7 

The temperature sensor 
(thermistor) has become 
disconnected or the heating 
element(s) have failed.  

Call service department on 
01704 502911  
Quoting the Serial Number 

8  or  9 

Fault on temperature sensor 
(thermistor). 

Call service department on 
01704 502911  
Quoting the Serial Number 

10 

Heating element(s) faulty .   

Call service department on 
01704 502911  
Quoting the Serial Number 

11 

The water supply has been 
interrupted and the level has 

Check water supply 
 

Содержание WB15














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды