Dimplex SI 130TU, Инструкция по установке и эксплуатации

Страница: 33 / 80

www.gdts.one 452237.66.52 · FD 9912 EN-13
SI 90TU - SI 130TU English
7 Complies with the European safety regulations
6
8 Additional model features
8.1 Water in device is protected against freezing
7
Yes
8.2 Max. operating overpressure (heat source/heat sink) bar 3.0
9 Heat output / COP
9.1 Heat output / coefficient of performance (COP)
5 8
EN 14511
Performance level 1 2
at B-5 / W45 kW / --- 37.3 / 3.4 71.6 / 3.2
at B0 / W55 kW / --- 40.9 / 3.1 78.9 / 3.0
at B0 / W45 kW / --- 42.5 / 3.8 81.7 / 3.6
at B0 / W35 kW / --- 45.5 / 5.0 86.0 / 4.7
1. If necessary, the operating range can be extended to a brine inlet temperature of -10 °C. In this case, the minimum brine concentration must be adjusted to 30%. (Freezing
temperature -17 °C)
For brine inlet temperatures of -10 °C to -5 °C, flow temperature increasing from 50 °C to 60 °C.
For brine inlet temperatures of -5 °C to 0°C, flow temperature increasing from 60 °C to 62 °C.
2. Operation is possible at brine inlet temperatures of up to +35 °C. For brine inlet temperatures of 25 °C to 35 °C, flow temperature decreasing from 62 °C to 58 °C.
3. The specified sound pressure level corresponds to the operating noise of the heat pump in heating operation at 55 °C flow temperature.
The specified sound pressure level represents the free sound area level. The measured value can deviate by up to 16 dB(A), depending on the installation location.
4. Note that additional space is required for pipe connections, operation and maintenance.
5. These data indicate the size and capacity of the system according to EN 14511. For an analysis of the economic and energy efficiency of the system, the bivalence point and
regulation should be taken into consideration. These specifications can only be achieved with clean heat exchangers. Information on maintenance, commissioning and oper-
ation can be found in the respective sections of the installation and operating instructions. The specified values, e.g. B0 / W55, have the following meaning: Heat source tem-
perature 0 °C and heating water flow temperature 55 °C.
6. See CE declaration of conformity
7. The heat circulating pump and the heat pump manager must always be ready for operation.
8. The coefficients of performance are valid with the circulating pumps included in the scope of supply.
1 Type and order code
SI 130TU
2 Design
Heat source Brine
2.1 Model Universal
2.2 Controller integrated
2.3 Thermal energy meter Integrated
2.4 Installation location Indoors
2.5 Performance levels 2
3 Operating limits
3.1 Heating water flow
1 2
°C
20 to 62 ± 2
3.2 Brine (heat source)
1 2
°C
-5 to +25
3.3 Antifreeze Monoethylene glycol
3.4 Minimum brine concentration (-13 °C freezing temperature) 25 %
4 Flow / sound
4.1 Heating water flow / free compression (max).
Nominal flow in accordance at B0...-3 / W35...28 m³/h / Pa 17.2 / 58000
at B0...-3 / W45...38 m³/h / Pa 16.5 / 60000
at B0...-3 / W55...45 m³/h / Pa 11.4 / 77000
Minimum heating water flow m³/h / Pa 11.4 / 77000
4.2 Brine flow rate / free compression (max).
Nominal flow in accordance at B0...-3 / W35...28 m³/h / Pa 33.1 / 63000
at B0...-3 / W45...38 m³/h / Pa 30.2 / 79000
at B0...-3 / W55...45 m³/h / Pa 27.3 / 91000
Minimum brine flow rate m³/h / Pa 27.3 / 91000
4.3 Sound power level according to EN 12102 dB(A) 70
4.4 Sound pressure level at a distance of 1m
3
dB(A)
55
5 Dimensions, weight and filling quantity
5.1 Device dimensions
4
H x W x L mm
1890 x 1350 x 750
5.2 Weight of the transportable unit(s) incl. packaging kg 824
5.3 Device connections for heating inches Rp 2½“
5.4 Device connections for heat source Inches Rp 3“
5.5 Refrigerant / total filling weight type/kg R410A / 19.5
5.6 GWP value / CO
2
equivalent --- / t
2088 / 41
5.7 Refrigeration circuit hermetically sealed yes