background image

14

PROBLEM

CAUSE

SOLUTION

Heater

Heater is not turning off (Manually)

Improper operation

Refer to Operation Section

Defective Remote Switchboard

Replace Remote Switchboard

Defective Remote Control Receiver

Replace Remote Control Receiver.  Initialize Remote 

Control and Remote Control Receiver.

Heater is not turning on (Manually)

Improper operation

Refer to Operation Section

Heater has been disabled

Refer to Operation Section for instructions to enable 

heater.

Loose wiring

Trace wiring in unit

Defective Heater Assembly

Replace Heater Assembly

Defective Remote Control Receiver

Replace Remote Control Receiver.  Initialize Remote 

Control and Remote Control Receiver.

Heater is turning off after a couple 

of minutes of operation

Build up of dirt/dust in the Heater Assem-

bly

Ensure that exterior intake louvers and firebox cavity 

are free of dirt/dust.

Defective Heater Assembly

Replace Heater Assembly

Heater emits an odor

Normal Operation

Normal operation is when the heater emits an odor 

for a brief period after the heater is initially turned on.  

The heater is burning off any dust accumulated during 

manufacturing or operation.

Defective Heater Assembly

Replace Heater Assembly

Heater fan turns on but heater lacks 

heat

Improper operation

Refer to Operation Section

Loose wiring

Trace wiring in unit

Defective Heater Assembly

Replace Heater Assembly

Heating element is glowing red

Normal Operation

Small glowing sections of the element are considered 

normal.

Defective heater assembly

If larger glowing sections are causing the heater to 

trip the thermal cutout, unplug unit, discontinue use 

and replace heater assembly.

Noise

Excessive noise with the heater on

Dirty Heater Assembly

Ensure that exterior intake louvers and firebox cavity 

are free of dirt/dust.

Defective Heater Assembly

Replace Heater Assembly

Grinding or excessive noise with the 

heater off

Flicker rod hitting or rubbing against inter-

nal components

Ensure rod is straight and mounted properly in the 

bracket, spinning freely away from other components. 

Replace if necessary.

Defective Flicker Motor

Replace Flicker Motor

Содержание DF3033ST















Отзывы: