Dillon FI-80 LCD Скачать руководство пользователя страница 18

Страница: 18 / 19

APPENDIX C: DISPLAYED ERROR CODES

CODE

MEANING / POSSIBLE SOLUTION

Gross Overload. A load greater than the rated capacity has been applied
to the scale. Remove the load and verify operation. Contact your Dillon
distributor with any problems.

Err 0

Should not appear in normal operation. Contact your Dillon distributor.

Err 1

Should not appear in normal operation. Contact your Dillon distributor.

Err 2

Should not appear in normal operation. Contact your Dillon distributor.

Err 3

Non-volatile memory read error. One or more setup parameters have
been lost. Contact your Dillon distributor.

Err 4

Non-volatile memory write error. Contact your Dillon distributor.

Err 5

Should not appear in normal operation. Contact your Dillon distributor.

Err 7

ADC reading error. Contact your Dillon distributor.

Err 9

Calibration value read error. Contact your Dillon distributor.

Indicates that the battery voltage is too low for normal operation.
Recharge the battery.

Содержание FI-80 LCD




















Результаты поиска

Содержание FI-80 LCD

Отзывы:

Похожие инструкции для FI-80 LCD

Бренды по названию

Популярные бренды

Dillon FI-80 LCD, Руководство пользователя

Результаты поиска

Содержание FI-80 LCD

Отзывы:

Похожие инструкции для FI-80 LCD

Бренды по названию

Популярные бренды