background image

 

 

9

 / 

15

 

 

 

NOTE

: If you connected to an access point but the connection has 

been dropped soon, please check security settings and re-check 
password spelling. 

 

2.2.2 Using WPS Connect 

 

Wi-Fi Protected Setup (WPS) is the latest wireless network 

technology which makes wireless network setup become very 
simple. If you have WPS-enabled wireless access point, and you 
want to establish a secure connection to it, you don‟t have to 
configure the wireless access point and setup data encryption by 
yourself. All you have to do is to go to the WPS setup page of this 
wireless card, click a button, and then press a specific button or 
enter a set of 8-digit code on the wireless access point you wish to 
establish a secure connection - just three simple steps! 

 

For older wireless access points, it‟s possible to perform a 

firmware upgrade to become a WPS-enabled access point. Since 
they may not have a hardware button to press for WPS setup, you 
can use an alternative WPS setup method - input the pin code. 
Every WPS-compatible wireless network card support pin code 
configuration method; you can just input the code to wireless 
access point, and the wireless access point and wireless network 
card will do the rest for you. 

 

This wireless network card is compatible with WPS. To use this 

function, the wireless access point you wish to connect to must 
support WPS function too. Now, please follow the following 
instructions to establish secure connection between WPS-enabled 
wireless access point and your wireless network card. 

 

This wireless network card supports 2 kinds of WPS: PIN code 

and Push-Button. 

 

Please follow the following instructions to setup WPS: 

 

1.

 

    Right-click Client configuration utility icon, and click „

Open 

Config Utility

‟. 

 

Содержание U1233
















Отзывы: