Digital Watchdog MEGApix DWC-MVT4Wi28 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 63

background image

2. Click “Enable alarm” and set the alarm holding time.
3. Set alarm trigger options. The setup steps are the same as motion detection.
Please refer to motion detection chapter for details.

⚫

SD Card Error

When there are some errors in writing SD card, the corresponding alarms will be
triggered.
1. Go to Config

→

Alarm

→

Anomaly

→

SD Card Error as shown below.

2. Click “Enable alarm” and set the alarm holding time.
3. Set alarm trigger options. Trigger alarm out, Email and FTP. The setup steps are
the same as motion detection. Please refer to

motion detection

chapter for details.

Note: SD card full and SD card error are only available for the models with SD slot.

⚫

IP Address Conflict

1. Go to Config

→

Alarm

→

Anomaly

→

IP Address Collision as shown below.

2. Click “Enable alarm” and set the alarm holding time.
3. Trigger alarm out. When the IP address of the camera is in conflict with the IP
address of other devices, the system will trigger the alarm out.

⚫

Cable Disconnection

1. Go to Config

→

Alarm

→

Anomaly

→

Cable Disconnected as shown below.

2

6

«
...
24
25
26
27
28
...
»

Содержание MEGApix DWC-MVT4Wi28
































































Отзывы:

Нет отзывов

Похожие инструкции для MEGApix DWC-MVT4Wi28

Бренд: DataSafe Страницы: 4

Бренд: PRODIS Страницы: 12

Бренд: Vello Страницы: 12

Бренд: Angekis Страницы: 26

Бренд: Flymemo Страницы: 22

NVAHD-2DN5504MD/IR-1

Бренд: Novus Страницы: 28

Бренд: Zip Страницы: 14

Бренд: aqprox! Страницы: 41

Бренд: D-MAX Страницы: 26

Бренд: Camlux Страницы: 90

Бренд: Defender Страницы: 68

Бренд: IP-Cam Страницы: 36

Бренд: Rapala Страницы: 8

Бренд: AEE Страницы: 18

Extreme X MGOVS015

Бренд: migear Страницы: 49

Бренд: Baader Planetarium Страницы: 18

Q-SYS NC Series

Бренд: QSC Страницы: 16

Бренд: Siqura Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды