background image

Timing Snapshot: Enable timing snapshot first and then set the snapshot interval and 
schedule. The setup steps of schedule are the same as the schedule recording (See 

Schedule Recording

).

6.2 Image Configuration

Image Configuration includes Display, Video/Audio, OSD, Video Mask and ROI Config.

6.2.1  Display Configuration

Go to  Image

Display  interface as shown below.  The  image’s brightness, contrast, 

hue  and  saturation  and  so  on  for  common,  day  and  night  mode  can  be  set  up 
separately. The image effect can be quickly seen by switching the configuration file.

Brightness: Set the brightness level of the camera’s image. 
Contrast: Set the color difference between the brightest and darkest parts.
Hue: Set the total color degree of the image.
Saturation: Set the degree of color purity. The purer the color, the brighter the image
is.
Sharpness: Set the resolution level of the image plane and the sharpness level of the
image edge.
Noise Reduction: Decrease the noise and make the image more thorough. Increasing
the  value  will  make  the  noise  reduction  effect  better  but  it  will  reduce  the  image

 

1

7

Содержание MEGApix DWC-MVT4Wi28
































































Отзывы: