DIGITAL-LOGIC MICROSPACE MSEP800, Техническое руководство пользователя

Страница: 73 / 140

DIGITAL-LOGIC AG
MSEP800 Manual V1.0G
73
J20 IrDa
Pin
Signal Pin Signal
Pin 1 = VCC 5V Pin 2 = IR TX
Pin 3 = IR RX Pin 4 = GND
BIOS settings:
You have to enable the UART A of the GeodeLX in the bios setup:
F1 -> Motherboard device configuration -> I/O configuration:
-
UART port A = enabled
-
UART mode = SIR/CIR
ATTENTION !
Do never set the UART A mode to “Serial – 16550 compatible” or “Extended” if a IrDa diode is con-
nected to the J20. Otherwise the diode will be destroyed!
X6 MiniPCI interface
Pin:
Signal: Pin: Signal: Pin: Signal: Pin: Signal:
1 TIP 2 RING 63 3.3V 64 FRAME#
3 8PMJ-3 4 8PMJ-1 65 CLKRUN# 66 TRDY#
5 8PMJ-6 6 8PMJ-2 67 SERR# 68 STOP#
7 8PMJ-7 8 8PMJ-4 69 GROUND 70 3.3V
9 8PMJ-8 10 8PMJ-5 71 PERR# 72 DEVSEL#
11 LED1_GRNP 12 LED2_YELP 73 C/BE[1]# 74 GROUND
13 LED1_GRNN 14 LED2_YELN 75 AD[14] 76 AD[15]
15 CHSGND 16 RESERVED 77 GROUND 78 AD[13]
17 INTB# 18 5V 79 AD[12] 80 AD[11]
19 3.3V 20 INTA# 81 AD[10] 82 GROUND
21 RESERVED 22 RESERVED 83 GROUND 84 AD[09]
23 GROUND 24 3.3VAUX 85 AD[08] 86 C/BE[0]#
25 CLK 26 RST# 87 AD[07] 88 3.3V
27 GROUND 28 3.3V 89 3.3V 90 AD[06]
29 REQ# 30 GNT# 91 AD[05] 92 AD[04]
31 3.3V 32 GROUND 93 RESERVED 94 AD[02]
33 AD[31] 34 PME# 95 AD[03] 96 AD[00]
35 AD[29] 36 RESERVED 97 5V 98 RESERVED_WIP5
37 GROUND 38 AD[30] 99 AD[01] 100 RESERVED_WIP5
39 AD[27] 40 3.3V 101 GROUND 102 GROUND
41 AD[25] 42 AD[28] 103 AC_SYNC 104 M66EN
43 RESERVED 44 AD[26] 105 AC_SDATA_IN 106 AC_SDATA_OUT
45 C/BE[3]# 46 AD[24] 107 AC_BIT_CLK 108 AC_CODEC_ID0#
47 AD[23] 48 IDSEL 109 AC_CODEC_ID1# 110 AC_RESET#
49 GROUND 50 GROUND 111 MOD_AUDIO_MON 112 RESERVED
51 AD[21] 52 AD[22] 113 AUDIO_GND 114 GROUND
53 AD[19] 54 AD[20] 115 SYS_AUDIO_OUT 116 SYS_AUDIO_IN
55 GROUND 56 PAR 117 SYS_AUDIO_OUT
GND 118 SYS_AUDIO_IN
GND
57 AD[17] 58 AD[18] 119 AUDIO_GND 120 AUDIO_GND
59 C/BE[2]# 60 AD[16] 121 RESERVED 122 MPCIACT#
61 IRDY# 62 GROUND 123 VCC5VA 124 3.3VAUX