background image

Prioris HX 6000 Server Powergrade Kit

11

Install any Video Option Card

If you previously removed a video option card, you can install it again.

Replace the Panel and Reconnect the Cables

1.  Install the left side panel and lock the server. The server will not

power up with the side panel removed.

2.  Connect the cables, the monitor power cord, and the server

power cord to the back of the server.

Run the System Configuration Utility (SCU)

The SCU enables you to check or change your server’s configuration.
Run the SCU to configure your server for the new CPU chip or
module.

To start and run the SCU:

1.  Insert the SCU diskette into drive A and turn on your server. The

diskette should boot automatically.

2.  When the SCU title appears, press any key to continue.

Afterwards, follow the instructions on your screen to access the
SCU main menu.

3.  From the main menu, press the up or down arrow to highlight an

item and then press Enter to select it. Press F1 at any time for
help about a selection.

4.  From the main menu select Configure Computer and then View

and Edit Details. Example:

If you installed a video option card, select the Advanced Control
Group and disable the Embedded - PCI VGA controller.

5.  Select Save and Exit to configure your server for the CPU

module.

6.  When complete, remove the SCU diskette from drive A.

Содержание Prioris HX 6000


















Отзывы: