Digital deep sea DSE5220 Скачать руководство пользователя страница 3

Страница: 3 / 53

DSE Model 5220 Automatic Mains Failure & Instrumentation System Operators Manual

5220 OPERATING MANUAL ISSUE 5.1 18-Jun-07 AM

TABLE OF CONTENTS

Section

Page

INTRODUCTION .............................................................................................. 5

CLARIFICATION OF NOTATION USED WITHIN THIS PUBLICATION. ........ 5

OPERATION .................................................................................................... 6

3.1

AUTOMATIC MODE OF OPERATION ............................................................................... 6

3.2

MANUAL OPERATION ....................................................................................................... 8

3.3

TEST OPERATION .............................................................................................................. 9

PROTECTIONS .............................................................................................. 10

4.1

WARNINGS ....................................................................................................................... 11

4.2

ANALOGUE PRE-ALARMS ............................................................................................. 11

4.3

HIGH CURRENT WARNING ALARM ............................................................................... 12

4.4

SHUTDOWNS .................................................................................................................... 13

4.5

HIGH CURRENT SHUTDOWN ALARM ........................................................................... 15

4.6

ELECTRICAL TRIPS ......................................................................................................... 15

LCD INDICATORS AND LOGO INSERT ....................................................... 16

DESCRIPTION OF CONTROLS .................................................................... 17

6.1

TYPICAL LCD DISPLAY SCREENS ................................................................................ 18

6.2

LCD DISPLAY AREAS ...................................................................................................... 19

6.3

VIEWING THE INSTRUMENTS ........................................................................................ 20

6.4

VIEWING THE EVENT LOG .............................................................................................. 21

6.5

INDICATORS ..................................................................................................................... 22

6.6

CONTROLS ....................................................................................................................... 22

FRONT PANEL CONFIGURATION ............................................................... 23

7.1

ACCESSING THE FRONT PANEL CONFIGURATION EDITOR .................................... 23

7.1.1

ENTERING THE CONFIGURATION EDITOR PIN NUMBER ................................... 23

7.1.2

EDITING AN ANALOGUE VALUE ............................................................................. 24

7.1.3

EDITING THE CURRENT DATE/TIME ...................................................................... 26

INSTALLATION INSTRUCTIONS .................................................................. 27

8.1

PANEL CUT-OUT .............................................................................................................. 27

8.2

COOLING........................................................................................................................... 27

8.3

UNIT DIMENSIONS ........................................................................................................... 27

8.4

FRONT PANEL LAYOUT .................................................................................................. 28

8.5

REAR PANEL LAYOUT .................................................................................................... 28

ELECTRICAL CONNECTIONS ...................................................................... 29

9.1

CONNECTION DETAILS................................................................................................... 29

9.1.1

PLUG “A” 8 WAY ........................................................................................................ 29

9.1.2

PLUG “B” 11 WAY ...................................................................................................... 29

9.1.3

PLUG “C” 3 WAY (NOT FITTED) ............................................................................... 29

9.1.4

PLUG “D” 4 WAY (OPTIONAL) .................................................................................. 30

9.1.5

PLUG “E” 8 WAY ........................................................................................................ 30

9.1.6

PLUG “F” 4 WAY ........................................................................................................ 30

9.1.7

PLUG “G” 5 WAY ........................................................................................................ 30

9.1.8

PLUG “H” 4 WAY ........................................................................................................ 31

9.1.9

PC CONFIGURATION INTERFACE CONNECTOR .................................................. 32

9.1.10

EXPANSION OUTPUT CONNECTOR ....................................................................... 32

9.2

CONNECTOR FUNCTION DETAILS ................................................................................ 33

9.2.1

PLUG “A” 8 WAY ........................................................................................................ 33

9.2.2

PLUG “B” 11 WAY ...................................................................................................... 33

9.2.3

PLUG “C” 3 WAY (NOT FITTED) ............................................................................... 34

9.2.4

PLUG “D” 4 WAY (OPTIONAL) .................................................................................. 34

9.2.5

PLUG “E” 8 WAY ........................................................................................................ 34

9.2.6

PLUG “F” 4 WAY ........................................................................................................ 34

CALL US TODAY

1-888-POWER-58

REQUEST A QUOTE

[email protected]

SHOP ONLINE

www.genpowerusa.com

Содержание DSE5220






















































Результаты поиска

Содержание DSE5220

Отзывы:

Бренды по названию

Популярные бренды

Digital deep sea DSE5220, Руководство по эксплуатации

Результаты поиска

Содержание DSE5220

Отзывы:

Бренды по названию

Популярные бренды