manualshive.com logo in svg

Digi XStream-PKG-R RS-232, Руководство пользователя

Поделиться
Скачать
Digi XStream-PKG-R RS-232 Скачать руководство пользователя страница 30

XStream

‐

PKG

‐

R™

 

RS

‐

232/422/485

 

RF

 

Modem

 

User’s

 

Guide

 

 

MK (Address Mask) Command 

<Networking> MK Command is used to set/read 
the Address Mask.  

All data packets contain the Destination Address 
of the transmitting modem. When an RF data 
packet is received, the transmitter’s Destination 
Address is logically “ANDed” (bitwise) with the 
Address Mask of the receiver. The resulting value 
must match the Destination Address or the 
Address Mask of the receiver for the packet to be 
received and sent out the modem’s DO serial 
port. If the “ANDed” value does not match either 
the Destination Address or the Address Mask of 
the receiver, the packet is discarded. (All “0” 
values are treated as “irrelevant” values and are ignored.) 

AT Command: ATMK 
Binary Command: 0x12 (18 decimal) 
Parameter Range:  0 – 0xFFFF 
Default Parameter Value: 0xFFFF  

(Destination address (DT parameter) of the 

transmitting modem must exactly match the 

destination address of the receiving modem.) 
Number of bytes returned: 2 
Related Commands: DT (Destination Address),  

HP (Hopping Channel), ID (Modem VID), MY 

(Source Address) 

 

 

NB (Parity) Command 

AT Command: ATNB 
Binary Command: 0x23 (35 decimal) 
Parameter Range:  0 – 4 

 

Parameter 

Value 

Configuration 

 

0 

<Serial Interfacing> Select/Read parity settings 
for UART communications. 

 

 

8-bit (no parity or  

7-bit (any parity) 

 

1 8-bit 

even 

 

2 8-bit 

odd 

 

3 8-bit 

mark 

 

4 8-bit 

space 

Default Parameter Value: 0 
Number of bytes returned: 1 
Minimum Firmware Version Required: 4.27B 

 

 

 

 

 

 

 

 

 

 

 

PC (Power-up to AT Mode) Command 

AT Command: ATPC 
Binary Command: 0x1E (30 decimal) 
Parameter Range:  0 – 1 

 

Parameter 

Value 

Configuration 

 

0 

Power-up to Idle Mode 

 

1 

<Command Mode Options> PC Command allows 
the modem to power-up directly into AT 
Command Mode from reset or power-on. If PC 
Command is enabled with SM Parameter set to 1, 
the DI3 Pin (SLEEP) can be used to enter the 
modem into AT Command Mode. When the DI3 
pin is de-asserted (low), the modem will Wake-up 
into AT Command Mode. This behavior allows 
modem DTR emulation. 

Power-up to 

AT Command Mode 

Default Parameter Value: 0 
Number of bytes returned: 1 
Minimum Firmware Version Required: 4.22 

 

 

 

 

 

           

30

 

Содержание XStream-PKG-R RS-232













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды