manualshive.com logo in svg

Digi XStream-PKG-R RS-232, Руководство пользователя, Страница: 18 / 44

Поделиться
Скачать
Digi XStream-PKG-R RS-232 Скачать руководство пользователя страница 18

XStream

‐

PKG

‐

R™

 

RS

‐

232/422/485

 

RF

 

Modem

 

User’s

 

Guide

 

 

 

Cyclic Scanning.

 Each RF transmission consists of an RF Initializer and payload. The wake-up 

initializer contains initialization information and all receiving modems must wake during the 
wake-up initializer portion of data transmission in order to be synchronized with the transmitting 
modem and receive the data.  

Figure

 

3.8.

 

Correct

 

Configuration

 

(LH

 

>

 

SM)

 

Length

 

of

 

the

 

wake

‐

up

 

initializer

 

exceeds

 

the

 

time

 

interval

 

of

 

Cyclic

 

Sleep.

 

The

 

receiver

 

is

 

guaranteed

 

to

 

detect

 

the

 

wake

‐

up

 

initializer

 

and

 

receive

 

the

 

accompanying

 

payload

 

data.

 

 

 

 

 

 

 

 

 

 

Figure

 

3.9.

 

Incorrect

 

Configuration

 

(LH

 

<

 

SM)

 

Length

 

of

 

wake

‐

up

 

initializer

 

is

 

shorter

 

than

 

the

 

time

 

interval

 

of

 

Cyclic

 

Sleep.

 

This

 

configuration

 

is

 

vulnerable

 

to

 

the

 

receiver

 

waking

 

and

 

missing

 

the

 

wake

‐

up

 

initializer

 

(and

 

therefore

 

also

 

the

 

accompanying

 

payload

 

data).

 

 

 

 

 

 

 

 

 

 

           

18

 

Содержание XStream-PKG-R RS-232













































Отзывы:

Нет отзывов