Digi XStream-PKG-R RS-232 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 44

Digi XStream-PKG-R RS-232 Скачать руководство пользователя страница 2

XStream

‐

PKG

‐

R™

RS

‐

232/422/485

RF

Modem

User’s

Guide

©2006

‐

2007

Digi

International

Digi,

Digi

International,

the

Digi

logo,

and

XStream

are

trademarks

or

registered

trademarks

of

Digi

International,

Inc.

in

the

United

States

and

other

countries

worldwide.

All

other

trademarks

are

the

property

of

their

respective

owners.

Information

in

this

document

is

subject

to

change

without

notice

and

does

not

represent

a

commitment

on

the

part

of

Digi

International.

Digi

provides

this

document

“as

is,”

without

warranty

of

any

kind,

either

expressed

or

implied,

including,

but

not

limited

to,

the

implied

warranties

of

fitness

or

merchantability

for

a

particular

purpose.

Digi

may

make

improvements

and/or

changes

in

this

manual

or

in

the

product(s)

and/or

the

program(s)

described

in

this

manual

at

any

time.

ii

«
1
2
3
4
...
»

Содержание XStream-PKG-R RS-232













































Отзывы:

Нет отзывов