Digi XBee Cellular LTE Cat 1 страница 53 Скачать руководство пользователя

Страница: 53 / 91

AT commands

Network commands

Digi XBee Cellular LTE Cat 1 Embedded Modem User Guide

0 - diversity disabled

1 - diversity enabled

Default

Network commands

The following commands are network commands.

IP (IP Protocol)

Sets or displays the IP protocol used for client and server socket connections in IP socket mode.

Parameter range

Value

Description

0x00

UDP

0x01

TCP

0x02

SMS

0x03

Reserved

0x04

SSL over TCP communication

Default

0x01

TL (SSL/TLS Protocol Version)

Sets the SSL/TLS protocol version used for the SSL socket. If you change the

value, it does not

affect any currently open sockets. The value only applies to subsequently opened sockets.

Note

Due to known vulnerabilities in prior protocol versions, we strongly recommend that you use the

latest TLS version whenever possible.

Range

Value

Description

0x00

SSL v3

0x01

TLS v1.0

0x02

TLS v1.1

0x03

TLS v1.2

Default

0x03

Содержание XBee Cellular LTE Cat 1




























































































Результаты поиска

Содержание XBee Cellular LTE Cat 1

Отзывы:

Похожие инструкции для XBee Cellular LTE Cat 1

Бренды по названию

Популярные бренды

Digi XBee Cellular LTE Cat 1, Руководство пользователя

Результаты поиска

Содержание XBee Cellular LTE Cat 1

Отзывы:

Похожие инструкции для XBee Cellular LTE Cat 1

Бренды по названию

Популярные бренды