Digi XBee Cellular LTE Cat 1 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 91

Digi XBee Cellular LTE Cat 1 Скачать руководство пользователя страница 52

AT commands

Cellular commands

Digi XBee Cellular LTE Cat 1 Embedded Modem User Guide

52

MV (Modem Firmware Version)

Read the firmware version string for cellular component communications. See the related

(Firmware Version)

command.

Parameter range

N/A

Default

Set in the currently loaded firmware

DB (Cellular Signal Strength)

Reads the absolute value of the current signal strength to the cell tower in dB. If DB is blank, the XBee
Cellular Modem has not received a signal strength from the cellular component.

Parameter range

0x71 - 0x33 (-113 dBm to -51 dBm) [read-only]

Default

N/A

AM (Airplane Mode)

When set, the cellular component of the XBee Cellular Modem is fully turned off and no access to the
cellular network is performed or possible.

Parameter range

0 - 1

0 = Normal operation

1 = Airplane mode

Default

0

DV (Antenna Diversity)

Set and read the antenna diversity setting of the cellular component. When enabled, the cellular
component uses both antennas to improve receive sensitivity.

This setting is applied only while the XBee Cellular Modem is initializing the cellular component. After
changing this setting, you must:

1. Use

to write all values to flash.

2. Use

FR (Force Reset)

to reset the device.

3. Wait for the cellular component to be initialized:

AI (Association Indication)

reaches

0x00

.

4. Use

FR

to reset the device a second time.

5. Wait again for the cellular component to initialize:

AI

reaches

0x00

.

Parameter range

0 - 1

«
...
50
51
52
53
54
...
»

Содержание XBee Cellular LTE Cat 1




























































































Отзывы:

Нет отзывов