manualshive.com logo in svg

Digi XBee Cellular LTE Cat 1, Руководство пользователя, Страница: 34 / 91

Поделиться
Скачать
Digi XBee Cellular LTE Cat 1 Скачать руководство пользователя страница 34

Hardware

Antenna placement

Digi XBee Cellular LTE Cat 1 Embedded Modem User Guide

34

secondary port is optional. The secondary antenna improves receive performance in certain
situations, so we recommend it for best results.

Antenna placement

It is important to keep the antenna as far away from the XBee Cellular Modem and other metal
objects as possible. Often, small antennas are desirable, but at the cost of increasing size of dead
zones because of reduced range and efficiency.

We recommend that antennas do not touch each other, but the XBee Cellular Modem works if they do.
To optimize receive performance, orient the two antennas at right angles to each other.

SIM card

The XBee Cellular Modem uses the 4FF/nano SIM card size.

CAUTION!

Never insert or remove SIM card while the power is on!

The Associate LED

The following table describes the Associate LED functionality. For the location of the Associate LED on
the XBIB-U development board, see number 6 on the

XBIB-U_DEV reference

.

LED status

Blink
timing

Meaning

On, solid

Not joined to a mobile network.

Содержание XBee Cellular LTE Cat 1




























































































Отзывы:

Нет отзывов