Digi ConnectCore 6UL SBC Pro Скачать руководство пользователя

Страница: 40 / 54

ConnectCore 6UL SBC Pro interfaces

Additional expansion interfaces

ConnectCore 6UL SBC Pro Hardware Reference Manual

i.MX6UL SPI1 instance

One slave select line

Interrupt line

The following table shows the pinout of the SPI expansion connector (J34):

Pin Signal name

Description

3V3

3.3V power line

LCD_DATA20/SPI1_CLK

SPI clock line

LCD_DATA23/SPI1_MISO SPI

Master Input Slave Output

line

LCD_DATA22/SPI1_MOSI SPI

Master Output Slave Input

line

LCD_DATA21/SPI1_SS0

SPI

Slave Select

line

MCA_IO5

Connected to on-module MCA

SPI1_IRQ_N

Interrupt line, connected to i.MX6UL GPIO5_08

GND

Ground

GPIO

The ConnectCore 6UL SBC Pro has a 14-pin, 1.25 mm pitch expansion connector, which provides
access to several GPIO lines of the i.MX6UL, on-module MCA and I/O expander.

The pinout of the GPIO expansion connector (J30) is shown below:

Pin Signal name Description

IOEXP_3

Connected to I/O expander

IOEXP_6

Connected to I/O expander

IOEXP_4

Connected to I/O expander

IOEXP_5

Connected to I/O expander

3V3

3.3V power line

IOEXP_37

Connected to I/O expander

MCA_IO1

Connected to MCA

MCA_IO3

Connected to MCA

MCA_IO2

Connected to MCA

Not connected

EXP_GPIO_1

Connected to i.MX6UL GPIO1_IO5

EXP_GPIO_2

Connected to i.MX6UL GPIO1_IO3

EXP_GPIO_3

Connected to i.MX6UL GPIO1_IO2

GND

Ground

Содержание ConnectCore 6UL SBC Pro























































Результаты поиска

Содержание ConnectCore 6UL SBC Pro

Отзывы:

Похожие инструкции для ConnectCore 6UL SBC Pro

Бренды по названию

Популярные бренды

Digi ConnectCore 6UL SBC Pro, Справочник по аппаратуре

Результаты поиска

Содержание ConnectCore 6UL SBC Pro

Отзывы:

Похожие инструкции для ConnectCore 6UL SBC Pro

Бренды по названию

Популярные бренды