background image

2

3

PUSH

PUSH

 

1

2

3

L

R

Product Maintenance

Product Maintenance

Dust bin and filter screen cleaning                                                                                                                                         
                

          

Use and cleaning of side brush                                                                                 

          

Sensor cleaning

Installation of side brush      

                                                                           

          

Disassembly of side brush                                                                                     

Cleaning of side brush                                                                           

Notice:                                                                                                             

          

After removing the dust bin, please check whether there is any foreign matter in the 
suction port and clean it.
Open it from the flap "PUSH", take out the dust bin, open the door of the dust bin, and 
dump the internal garbage.
Hold the small handle of the HEPA and pull out the HEPA.
Wash the dust bin and filter screen with water and pat the accumulated dust on the HEPA.
After cleaning, put the HEPA back into the dust bin in order.
Cover the door of the dust bin and put it into the host.

At the time of installing, it shall be noted that the side 
brush should be consistent with the left (L) and right (R) 
of the bottom shell, and the parts are marked with "L" and 
"R". After one-to-one correspondence, press directly, and 
it will be OK after hearing the tone of clasping. 

At the time of disassembling, grasp the three brushes at 
the same time and pull them up. 

Check whether the side brush is damaged or has foreign 
matter. 
Clean the side brush with a cleaning tool or a piece of 
duster cloth. 
If crimping or deformation occurs, remove the side brush 
and keep it in warm water for about 5s. 
When the side brush is damaged and cannot be used, 
please replace it in time. 

Wipe the sensor with a cleaning tool or a piece of soft cloth, as the below figure show. 

Cliff  Sensor

Collision Rod Light Filter 

Rear Window

Notice: If L and R are installed incorrectly, the machine will 
shake when it runs. 

It is recommended to clean the dust bin once a week. 

It is recommended to wash the HEPA and filter screen once after using 15 - 30 days.

Before installation, please ensure that the filter screen and the HEPA are in a dry state.

Do not expose the filter screen and HEPA to the sun.

HEPA is a replaceable accessory.

Содержание D500 Pro










Отзывы: