Diamondback 64683 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 20

Diamondback 64683 Скачать руководство пользователя страница 8

Page 8

For technical questions, please call 1-888-866-5797.

Item 64683

Sa
FE
ty

Op
E

ra
ti

O

n

Maint

E

nanc

E

S

E

tup

aSSEMBLy

tO prEVEnt SEriOuS inJury FrOM acciDEntaL OpEratiOn:
turn the power Switch of the tool off, remove the Safety Key, and unplug the tool
from its electrical outlet before performing any procedure in this section.

note:

For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

installing Motor Head

1. Place three Screw Sleeves (128)

into top mounting holes on Water
Tray Frame (120) as shown.

2. Align the holes in the Motor Head

Assembly with the corresponding mounting
holes on the top of the Water Tray Frame.

3.

Insert three M10 x 60 Socket Head Cap

Screws (131) through three Spring
Washers (130), Flat Washers (129),
the Motor Head Assembly, and the
Water Tray Frame. Secure using M10
Lock Nuts (127). Finger tighten.

4. Place two Screw Sleeves (128)

into side mounting holes on Water
Tray Frame as shown.

5.

Insert two M10 x 60 Socket Head Cap

Screws (131) through two Spring Washers (130),
Flat Washers (129), the Motor Head Assembly,
and then into side mounting holes on the Water
Tray Frame. Secure using M10 Lock Nuts (127).

6.

Tighten three previously installed M10 x 60

Socket Head Cap Screws securely.

7. With assistance, place the completed

Motor Head / Water Tray Frame

assembly on the Water Tray (77).

Water

tray

Frame

Water tray Frame

Screw

Sleeve

Screw

Sleeve

Motor

Head

assembly

M10 x 60

cap Screw

M10

Lock nut

M10 Lock nut

Flat

Washer

Spring

Washer

M10 x 60

cap Screw

Flat

Washer

Spring

Washer

Motor Head installation

«
...
6
7
8
9
10
...
»

Содержание 64683





















Отзывы:

Нет отзывов