manualshive.com logo in svg

Diamondback 64683, Руководство пользователя и инструкции по безопасности, Страница: 14 / 20

Поделиться
Скачать
Diamondback 64683 Скачать руководство пользователя страница 14

Page 14

For technical questions, please call 1-888-866-5797.

Item 64683 

        

Sa
FE
ty

Op
E

ra
ti

O

n

Maint

E

nanc

E

S

E

tup

General Operating instructions

1.  Adjust the Miter, Bevel, and Depth 

settings as needed.  Refer to page 
12.  Lock all settings in place.

2.  Place the workpiece on the 

Table and firmly against the 
Miter Gauge and Fence.

3.  Make sure the workpiece is clear of 

the Blade and that the Switch is in the 
off-position, then plug in the tool.

4.  Insert the Safety Key and lift the Power 

Switch up to the ON position.

5.  With the Saw running, make sure the 

Pump is supplying enough water to 
the Blade.  If needed, dry your hands, 
turn off and unplug the Saw, adjust the 

Pump′s flow, dry your hands again, 

plug the Saw back in and turn on.

6.  Let the Blade build up to full 

speed before cutting.

7.  Use two hands and hold 

workpiece securely against Table 
and Fence at all times.  Feed 
the material into the Blade.

8.  When the cut is made, turn the Saw 

off.  Wait for the Blade to come to 
a complete stop before removing 
any part of the workpiece.

9.  To prevent accidents, turn off the tool, 

remove the Safety Key, and unplug the tool 
from its electrical outlet after use.  Clean, 
then store the tool indoors out of children’s 
reach.  Store the Safety Key separate 

from the tool and out of children′s reach.

Straight cut

Miter cut

Bevel cut

Содержание 64683





















Отзывы:

Нет отзывов