Diamondback 64683 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 20

Diamondback 64683 Скачать руководство пользователя страница 13

Page 13

For technical questions, please call 1-888-866-5797.

Item 64683

Sa

FE

ty

Op

E

ra

ti

O

n

Maint

E

nanc

E

S

E

tup

installing Extension tray

Standing at back of Saw, place the tabs on the
Extension Tray (149) into the corresponding
holes in the Water Tray and push the Extension
Tray down to a horizontal position.

Water tray

Extension

tray

Extension tray installation

Filling the Water tray

1. Place the Drain Plug into the hole on

the bottom of the Water Tray.

2. Fill the Water Tray with clean water up to

the Maximum Fill Line before every use.

nOticE:

Water level must be kept above Minimum

Fill Line at all times during operation or damage
to the Pump and/or Saw Blade will occur.

Workpiece and Work area Set up

1. Designate a work area that is clean and well-lit.

The work area must not allow access by children
or pets to prevent distraction and injury.

2. Route the power cord along a safe route to reach

the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.

3. There must not be objects, such as utility lines,

nearby that will present a hazard while working.

4. Keep workpieces pressed firmly against

the Table and Fence while cutting.

5. Mark cut lines using waterproof marker or crayon.

note:

This tool is intended for use on

man-made masonry and tile products only.

Filling Water tray

Drain plug

Maximum

Fill Line

Minimum

Fill Line

«
...
11
12
13
14
15
...
»

Содержание 64683





















Отзывы:

Нет отзывов